- 您现在的位置：买卖IC网 > PDF目录13122 > MAX1543ETP+ (Maxim Integrated Products)IC DC-DC CONV TFT-LCD 20-TQFN PDF资料下载
参数资料
| 型号： | MAX1543ETP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/20页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CONV TFT-LCD 20-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | 控制器，TFT LCD |
| 输入电压： | 2.6 V ~ 5.5 V |
| 输出数： | 2 |
| 输出电压： | 2.6 V ~ 13 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WQFN 裸露焊盘 |
| 供应商设备封装： | 20-TQFN-EP（5x5） |
| 包装： | 管件 |
TFT LCD DC-to-DC Converter with
Operational Amplifiers
Pin Description (continued)
MAX1542
14
PIN
MAX1543
14
NAME
IN
FUNCTION
Supply Voltage. IN can range from 2.6V to 5.5V.
Oscillator Frequency Select Input. Pull FREQ low or leave it unconnected for 640kHz
—
15
FREQ
operation. Connect FREQ high for 1.2MHz operation. This input has a 5μA pulldown
current.
Step-Up Converter Feedback Input. Regulates to 1.24V (nominal). Connect a resistor-
16
16
FB
divider from the output (V MAIN ) to FB to analog ground (AGND). Place the resistor-divider
within 5mm of FB.
17
17
COMP
Step-Up Regulator Error Amplifier Compensation Point. Connect a series RC from COMP
to AGND. See the Loop Compensation section for component selection guidelines.
High-Voltage Switch Delay Input. Connect a capacitor from DEL to AGND to set the high-
voltage switch startup delay. A 5μA current source charges C DEL .
For the MAX1542, the high-voltage switch between SRC and COM is disabled until V DEL
exceeds 1.24V. Following the delay period, CTL controls the state of the high-voltage
18
18
DEL
switch.
For the MAX1543, the switches between SRC, COM, and DRN are disabled and a 1k ?
pulldown between COM and PGND is enabled until V DEL exceeds 1.24V. Following the
delay period, the 1k ? pulldown is released and CTL controls the state of the high-voltage
switches (see the Delay Control Circuit section).
High-Voltage Switch Control Input. When CTL is high, the high-voltage switch between
COM and SRC is on and the high-voltage switches between COM and DRN (MAX1543)
19
19
CTL
are off. When CTL is low, the high-voltage switch between COM and SRC is off and the
high-voltage switches between COM and DRN (MAX1543) are on. CTL is inhibited by the
undervoltage lockout and when V DEL is less than 1.24V.
—
20
DRN
Switch Input. Drain of the internal high-voltage back-to-back P-channel MOSFETs
connected to COM.
Typical Application Circuits
The MAX1542 typical application circuit (Figure 1) and
the MAX1543 typical application circuit (Figure 2) gen-
erate an +8V source driver supply and approximately
+22V and -7V gate driver supplies for TFT displays. The
input voltage is from +2.6V to +5.5V. Table 1 lists rec-
ommended components and Table 2 lists contact infor-
mation for component suppliers.
Detailed Description
The MAX1542/MAX1543 include a high-performance
step-up regulator, two high-current operational ampli-
fiers, and startup timing and level-shifting functionality
useful for active matrix TFT LCDs. Figure 3 shows the
MAX1542/MAX1543 functional diagram.
Main Step-Up Converter
The MAX1542/MAX1543 main step-up converter
switches at 1.2MHz or 640kHz (MAX1543 only) (see the
Oscillator Frequency (FREQ) section). The devices
employ a current-mode, fixed-frequency, pulse-width
modulation (PWM) architecture to maximize loop band-
width providing fast transient response to pulsed loads
found in source drivers for TFT LCD panels. The high-
switching frequency also allows the use of low-profile
inductors and capacitors to minimize the thickness of
LCD panel designs. The integrated high-efficiency
MOSFET and the IC ’ s built-in digital soft-start function
reduce the number of external components required
while controlling inrush current. The output voltage of
the main step-up converter (V MAIN ) can be set from V IN
to 13V with an external resistive voltage-divider at FB.
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| RSM25DRUS | CONN EDGECARD 50POS DIP .156 SLD |
| RPR20-2415S-1F | CONV DC/DC 20W 12-36VIN 15VOUT |
| EMC26DRYH-S734 | CONN EDGECARD 52POS DIP .100 SLD |
| 400VXH150MEFCSN22X30 | CAP ALUM 150UF 400V 20% SNAP-IN |
| EMM15DSUS | CONN EDGECARD 30POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1543ETP+ | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1543ETP+T | 功能描述:LCD 驱动器 TFT LCD DC/DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1543ETP-T | 功能描述:LCD 驱动器 RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX1543EVKIT | 功能描述:显示开发工具 MAX1542/3 Eval Kit RoHS:否 制造商:4D Systems 产品:4Display Shields 工具用于评估:?OLED-160-G1, ?OLED-160-G2 接口类型:Serial 工作电源电压:5 V |
| MAX1544ETL | 功能描述:电压模式 PWM 控制器 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。