- 您现在的位置：买卖IC网 > PDF目录20755 > MAX1561ETA+T (Maxim Integrated)IC LED DRIVR WHITE BCKLGT 8-TDFN PDF资料下载
参数资料
| 型号： | MAX1561ETA+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR WHITE BCKLGT 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 恒定电流： | 是 |
| 拓扑： | PWM，升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光 |
| 类型 - 次要： | 白色 LED |
| 频率： | 800kHz ~ 1.25MHz |
| 电源电压： | 2.6 V ~ 5.5 V |
| 输出电压： | 26V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（3x3） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 85°C |
High-Efficiency, 26V Step-Up Converters
for Two to Six White LEDs
Pin Description
PIN
1
2
3
4
5
6
7
8
Exposed
Pad
NAME
OUT
IN
CTRL
CS
COMP
GND
PGND
LX
EP
FUNCTION
Overvoltage Sense. When V OUT is greater than 27V, the internal N-channel MOSFET turns off until V OUT
drops below 25V, then the IC reenters soft-start. Connect a 0.1μF capacitor from OUT to PGND.
Input Voltage Supply. Input voltage range is 2.6V to 5.5V. Connect a 2.2μF capacitor from IN to PGND.
Brightness Control Input. LED brightness is controlled by the voltage applied to CTRL. Varying the voltage
from 0.24V to 1.62V adjusts the brightness from dim to bright, respectively. Any voltage above 1.62V does
not increase brightness. If CTRL is held below 100mV for more than 8.2ms (16.4ms for the MAX1599), the
IC shuts down.
Current-Sense Feedback Input. Connect a resistor from CS to GND to set the LED bias current. The
voltage at CS regulates to V CTRL / 10 or 0.162V, whichever is lower.
Compensation Input. Connect a 0.1μF capacitor (C COMP ) from COMP to GND. C COMP stabilizes the
converter and controls soft-start. C COMP discharges to GND when in shutdown.
Ground. Connect to PGND and the exposed pad directly under the IC.
Power Ground. Connect to GND and the exposed pad directly under the IC.
Inductor Connection. This pin is high impedance during shutdown.
Ground. Connect directly to GND and PGND under the IC.
Detailed Description
The MAX1561/MAX1599s’ high efficiency and small size
make them ideally suited to drive up to six series-con-
nected LEDs. The device operates as a boost DC-DC
converter that regulates output current rather than volt-
age. The MAX1561/MAX1599 provide even illumination
by sourcing the same output current through each LED,
eliminating the need for expensive factory calibration.
The fast 1MHz (500kHz for the MAX1599) internal oscil-
lator allows for a small inductor and small input and out-
put capacitors while minimizing input and output ripple.
The single analog control input allows easy adjustment
of LED brightness and on/off control. This allows either
simple logic-level on/off control, analog voltage control,
or PWM duty-cycle control of both brightness and shut-
down. In shutdown, supply current is reduced to a low
0.3μA. A soft-start gradually illuminates the LEDs, elimi-
nating the inrush current during startup.
Soft-Start
The MAX1561/MAX1599 attain soft-start by charging
C COMP gradually with a current source. When V COMP
rises above 1.25V, the internal MOSFET begins switch-
ing at a reduced duty cycle. When V COMP rises above
2.25V, the duty cycle is at its maximum. See the Typical
Operating Characteristics for an example of soft-start
operation.
Shutdown
The MAX1561/MAX1599 enter shutdown when V CTRL is
less than 100mV for more than 8.2ms (16.4ms for the
MAX1599). In shutdown, supply current is reduced to
0.3μA by powering down the entire IC except for the
CTRL voltage-detection circuitry. C COMP is discharged
during shutdown, allowing the device to reinitiate soft-
start when it is enabled. Although the internal N-chan-
nel MOSFET does not switch in shutdown, there is still
a DC current path between the input and the LEDs
through the inductor and Schottky diode. The minimum
forward voltage of the LED array must exceed the max-
imum input voltage to ensure that the LEDs remain off
in shutdown. However, with two or more LEDs, the for-
ward voltage is large enough to keep leakage current
low, less than 1μA (typ). Typical shutdown timing char-
acteristics are shown in the Typical Operating
Characteristic s.
Overvoltage Protection
Overvoltage lockout (OVLO) occurs when V OUT is
above 27V. The protection circuitry stops the internal
MOSFET from switching and causes V COMP to decay
to 0V. The device comes out of OVLO and into soft-
start when V OUT falls below 25V.
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ABM36DRMT-S288 | CONN EDGECARD EXTEND 72POS .156 |
| RYM36DRSN-S273 | CONN EDGECARD 72POS DIP .156 SLD |
| MAX16836ASA+T | IC LED DRIVER 350MA 8-SOIC |
| RSM36DRSN-S273 | CONN EDGECARD 72POS DIP .156 SLD |
| REC3-2412DRW/H/B/M | CONV DC/DC 3W 18-36VIN +/-12VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1561EVKIT | 功能描述:LED 照明开发工具 Evaluation Kit for MAX1561 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX1562ESA | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1562ESA+ | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1562ESA+C4H | 功能描述:电源开关 IC - USB Programmable 4A USB Current-Limited Switches with Autoreset and Fault Blanking RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1562ESA+T | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。