- 您现在的位置：买卖IC网 > PDF目录383326 > MAX1563ETC (MAXIM INTEGRATED PRODUCTS INC) Programmable 4A USB Current-Limited Switches with Autoreset and Fault Blanking PDF资料下载
参数资料
| 型号： | MAX1563ETC |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Programmable 4A USB Current-Limited Switches with Autoreset and Fault Blanking |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC12 |
| 封装： | 4 X 4 MM, 0.9 MM HEIGHT, MO-220A, QFN-12 |
| 文件页数： | 9/12页 |
| 文件大小： | 436K |
| 代理商： | MAX1563ETC |
Applications Information
Input Power Supply and Capacitance
Connect both IN inputs together externally. IN powers
the internal control circuitry and charge pump for the
switch, allowing a decreased R
ON
. Bypass IN to GND
with a 1μF ceramic capacitor. When driving inductive
loads or operating from inductive sources, which may
occur when the device is powered by long leads or PC
traces, larger input bypass capacitance is required to
prevent voltage spikes from exceeding the absolute
maximum ratings during short-circuit events.
Output Capacitor
Bypass OUT to GND with a 4.7μF ceramic capacitor for
local decoupling. Additional bulk capacitance (up to
470μF) reduces output-voltage transients under dynam-
ic load conditions. Using output capacitors greater than
470μF might assert
FAULT
if the current limit cannot
charge the output capacitor within the 20ms fault-
blanking period. In addition to bulk capacitance, small-
value (0.1μF or greater) ceramic capacitors improve the
output
’
s resilience to electrostatic discharge (ESD).
Driving Inductive Loads
A wide variety of devices (mice, keyboards, cameras,
and printers) typically connect to the USB port with
cables, which might add an inductive component to the
load. This inductance causes the output voltage at the
USB port to oscillate during a load step. The
MAX1562/MAX1562H/MAX1563 drive inductive loads,
but avoid exceeding the device
’
s absolute maximum
ratings. The load inductance is usually relatively small,
and the MAX1562/MAX1562H/MAX1563s
’
input
includes a substantial bulk capacitance from an
upstream regulator, as well as local bypass capacitors,
limiting overshoot. If severe ringing occurs because of
large-load inductance, clamp the MAX1562/MAX1562H/
MAX1563 outputs below +6V and above -0.3V.
Turn-On and Turn-Off Behavior
When turned on, the MAX1562/MAX1562H/MAX1563 out-
put ramps up over 2.5ms to eliminate load transients on
the upstream power source. When turned off, the output
ramps down for 800μs. Under fault conditions, the output
of the switches turns off rapidly to provide maximum safe-
ty for the upstream power source and downstream
devices. Internal blocks shut down to minimize supply
current when the switch is off.
M
Programmable 4A USB Current-Limited
Switches with Autoreset and Fault Blanking
_______________________________________________________________________________________
9
Table 2. Current Limiting and Fault Behavior
CONDITION
MAX1562/MAX1562H/MAX1563 BEHAVIOR
Output Short-Circuit
(V
OUT
< +1V)
If a short is detected at the output, the channel turns off, and the blanking timer begins.
FAULT
remains high during the blanking timeout period.
If the short persists during the fault-blanking period, the output pulses at 0.30 x I
LIM
RMS. If the short
is removed before the 20ms short-circuit blanking timeout period, the next ramped current pulse soft-
starts the output.
FAULT
remains high.
If the short-circuit persists after the fault-blanking period.
FAULT
goes low, autoreset mode begins,
and the output sources 25mA.
If the output voltage rises above 0.5V for 20ms, the channel resets, the output turns on, and
FAULT
goes high.
Output Overload Current
(V
OUT
> +1V)
If an overload occurs, output current regulates at I
LIM
and the blanking timer turns on.
FAULT
remains
high during the blanking timeout period.
Continuous current at I
LIM
persists until either the 20ms blanking period expires or a thermal
fault occurs.
If overcurrent persists after 20ms,
FAULT
goes low, autoreset mode is enabled, and the output
sources 25mA.
If the output voltage rises above 0.5V for 20ms, the channel resets, the output turns on, and
FAULT
goes high (see the Overload Response into 1.4
graph in the
Typical Operating
Characteristics
section).
Thermal Fault
(T
J
> +160
°
C)
A junction temperature of +160
o
C immediately asserts
FAULT
low (the blanking timeout period
does not apply for thermal faults) and turns off the switch. When the junction cools by 15
°
C, the
thermal fault is cleared and
FAULT
goes high. Note that if other fault conditions are present when
a thermal fault clears, those fault states take effect.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1562HESA | AC MEXICO |
| MAX1565 | Small, High-Efficiency, Five-Channel Digital Still Camera Power Supply |
| MAX1565ETJ | Small, High-Efficiency, Five-Channel Digital Still Camera Power Supply |
| MAX1566-MAX1567 | Six-Channel, High-Efficiency, Digital Camera Power Supplies |
| MAX156ACNG | 8-/4-Channel ADCs with Simultaneous T/Hs and Reference |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1563ETC+ | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1563ETC+T | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1563ETC-T | 功能描述:电源开关 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1563EVKIT | 制造商:Maxim Integrated Products 功能描述:PROGRAMMABLE 4A USB CURRENT-LIMITED - Rail/Tube |
| MAX1564ETE | 功能描述:电源开关 IC - USB Triple 1.2A USB Switch RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。