参数资料
型号: MAX1565ETJ+
厂商: Maxim Integrated Products
文件页数: 15/26页
文件大小: 0K
描述: IC DGTL CAM PWR-SUP 5CH 32TQFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 60
应用: 转换器控制器,数字式相机
输入电压: 0.7 V ~ 5.5 V
输出数: 5
输出电压: 3.3V,1.25 V ~ 5.5 V
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 32-WFQFN 裸露焊盘
供应商设备封装: 32-TQFN-EP(5x5)
包装: 管件
Small, High-Efficiency, Five-Channel
Digital Still Camera Power Supply
Note that the step-up output supplies both the step-up
load and the step-down input current when the step-
down is powered from the step-up. The step-down
input current reduces the available step-up output cur-
rent for other loads.
Direct Battery Step-Down Operation
The step-down converter can also be operated directly
from the battery as long as the voltage at INSD does
not exceed OUTSU by more than a Schottky diode for-
ward voltage. When using this connection, connect a
Schottky diode from the battery input to OUTSU. There
is also an internal 10k ? resistance from OUTSU to
INSD, which adds a small additional current drain (of
approximately (V OUTSU - V INSD )/10k ? from OUTSU
when INSD is not connected directly to OUTSU.
Step-down direct battery operation improves efficiency
for the step-down output (up to 95%), but limits the
upper limit of the output voltage to 200mV less than the
minimum battery voltage. In 1-cell Li+ designs (with a
2.7V min), the output can be set up to 2.5V. In 2-cell
alkaline or NiMH designs, the output may be limited to
1.5V or 1.8V, depending on the minimum allowed cell
voltage.
The step-down can only be briefly operated in dropout
since the MAX1565 fault protection detects the out-of-
regulation condition and activates after 100,000 OSC
cycles, or 200ms at 500kHz. At that point, all MAX1565
channels shut down.
FB
COMP
Auxiliary DC-to-DC Controllers
The three auxiliary controllers operate as fixed-frequency
voltage-mode PWM controllers. They do not have
internal MOSFETs, so output power is determined by
external components. The controllers regulate output
voltage by modulating the pulse width of the DL_ drive
signal to an external N-channel MOSFET switch.
Figure 3 shows a functional diagram of an AUX
controller channel. A sawtooth oscillator signal at OSC
governs timing. At the start of each cycle, DL_ goes
high, turning on the external N-FET switch. The switch
then turns off when the internally level-shifted sawtooth
rises above COMP_ or when the maximum duty cycle is
exceeded. The switch remains off until the start of the
next cycle. A transconductance error amplifier forms an
integrator at COMP_ so that DC high-loop gain and
accuracy can be maintained.
The auxiliary controllers do not start until the step-up
DC-to-DC output is in regulation. If the step-up, step-
down, or any of the auxiliary controllers remains faulted
for 100,000 OSC cycles, then all MAX1565 channels
latch off.
LEVEL
R
Q
DL_
SHIFT
REFI
SOFT-
S
REF
START*
0.85 REF
CLK
OSC
FAULT
*SOFT-START RAMPS REFI FROM 0V TO V REF IN 4096 CLOCK CYCLES.
Figure 3. PWM Auxiliary Controller Functional Diagram
PROTECTION
ENABLE
______________________________________________________________________________________
15
相关PDF资料
PDF描述
MAX1567ETL+ IC DGTL CAM PWR-SUP 6CH 40TQFN
MAX1572ETC180+ IC REG BUCK SYNC 1.8V .8A 12TQFN
MAX1579ETG+ IC PS BIAS/WHITE LED TFT 24-TQFN
MAX1584ETJ+ IC DGTL CAM PWR-SUP 5CH 32TQFN
MAX1586AETM+ IC POWER MANAGEMENT 48-TQFN
相关代理商/技术参数
参数描述
MAX1565ETJ+ 功能描述:PMIC 解决方案 5Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MAX1565ETJ+T 功能描述:PMIC 解决方案 5Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MAX1565ETJ-T 功能描述:PMIC 解决方案 5Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel
MAX1565EVKIT 制造商:Maxim Integrated Products 功能描述:SMALL, HIGH-EFFICIENCY, FIVE-CHANNEL DSC - Bulk
MAX1566ETL 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel