- 您现在的位置：买卖IC网 > PDF目录383326 > MAX1566-MAX1567 (Maxim Integrated Products, Inc.) Six-Channel, High-Efficiency, Digital Camera Power Supplies PDF资料下载
参数资料
| 型号： | MAX1566-MAX1567 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | Six-Channel, High-Efficiency, Digital Camera Power Supplies |
| 中文描述： | 六通道，高效率，数码相机电源 |
| 文件页数： | 15/35页 |
| 文件大小： | 1134K |
| 代理商： | MAX1566-MAX1567 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
M
Six-Channel, High-Efficiency, Digital
Camera Power Supplies
______________________________________________________________________________________
15
Detailed Description
The MAX1566/MAX1567 include the following blocks to
build a multiple-output digital camera power-supply
system. Both devices can accept inputs from a variety
of sources including 1-cell Li+ batteries, 2-cell alkaline
or NiMH batteries, and even systems designed to
accept both battery types. The MAX1566/
MAX1567 include six DC-to-DC converter channels to
generate all required voltages:
Step-up DC-to-DC converter (_SU pins) with on-chip
power FETS
Main DC-to-DC converter (_M pins) with on-chip
power FETS that can be configured as either a step-
up or step-down DC-to-DC converter
Step-down core DC-to-DC converter with on-chip
MOSFETs (_SD pins)
AUX1 DC-to-DC controller for boost and flyback
converters
AUX2 DC-to-DC controller for boost and flyback
converters (MAX1566)
AUX2 DC-to-DC controller for inverting DC-to-DC
converters (MAX1567)
AUX3 DC-to-DC controller for white LED as well as
conventional boost applications; includes open LED
overvoltage protection
Step-Up DC-to-DC Converter
The step-up DC-to-DC switching converter typically is
used to generate a 5V output voltage from a 1.5V to
4.5V battery input, but any voltage from V
IN
to 5V can
be set. An internal NFET switch and external synchro-
nous rectifier allow conversion efficiencies as high as
95%. Under moderate to heavy loading, the converter
operates in a low-noise PWM mode with constant
frequency and modulated pulse width. Switching
harmonics generated by fixed-frequency operation are
consistent and easily filtered. Efficiency is enhanced
under light (<75mA typ) loading by an Idle Mode that
switches the step-up only as needed to service the
load. In this mode, the maximum inductor current is
150mA for each pulse.
Main DC-to-DC Converter (Step-Up or
Step-Down)
The main converter can be configured as a step-up
(Figure 2) or a step-down converter (Figure 1) with the
SUSD pin. The main DC-to-DC converter is typically
used to generate 3.3V, but any voltage from 2.7V to 5V
can be set; however, the main output must not be set
higher than the step-up output (PVSU).
An internal MOSFET switch and synchronous rectifier
allow conversion efficiencies as high as 95%. Under
moderate to heavy loading, the converter operates in a
low-noise PWM mode with constant frequency and
modulated pulse width. Switching harmonics generated
by fixed-frequency operation are consistent and easily
filtered. Efficiency is enhanced under light loading
(<150mA typical for step-up mode, <100mA typical for
step-down mode) by assuming an Idle Mode during
which the converter switches only as needed to service
the load.
Step-down operation can be direct from a Li+ cell if the
minimum input voltage exceeds the desired output by
approximately 200mV. Note that if the main DC-to-DC,
operating as a step-down, operates in dropout, the
overload protection circuit senses an out-of-regulation
condition and turns off all channels.
Li+ to 3.3V Boost-Buck Operation
When generating 3.3V from an Li+ cell, boost-buck
operation may be needed so a regulated output can be
maintained for input voltages above and below 3.3V. In
that case, it may be best to configure the main convert-
er as a step-down (SUSD = GND) and to connect its
input, PVM, to the step-up output (PVSU), set to a volt-
age at or above 4.2V (Figures 1 and 3). The compound
efficiency with this connection is typically up to 90%.
This connection is also suitable for designs that must
operate from both 1-cell Li+ and 2 AA cells.
Note that the step-up output supplies both the step-up
load and the main step-down input current when the
main is powered from the step-up. The main input cur-
rent reduces the available step-up output current for
other loads.
2 AA to 3.3V Operation
In designs that operate only from 2 AA cells, the main
DC-to-DC can be configured as a boost converter (SUSD
= PVM) to maximize the 3.3V efficiency (Figure 2).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX156ACNG | 8-/4-Channel ADCs with Simultaneous T/Hs and Reference |
| MAX156BCNG | 8-/4-Channel ADCs with Simultaneous T/Hs and Reference |
| MAX156BENG | 8-/4-Channel ADCs with Simultaneous T/Hs and Reference |
| MAX155AEPI | 8-/4-Channel ADCs with Simultaneous T/Hs and Reference |
| MAX155BEPI | CONN HEADER 2POS R/A W/CLIP SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1567ETL | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1567ETL+ | 功能描述:PMIC 解决方案 6Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1567ETL+T | 功能描述:PMIC 解决方案 6Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1567ETL-T | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1567EVKIT | 制造商:Maxim Integrated Products 功能描述:6-CHANNEL HIGH EFFICIENCY DIGITAL CAMERA POWE - Bulk |
发布紧急采购，3分钟左右您将得到回复。