- 您现在的位置：买卖IC网 > PDF目录383326 > MAX1574 (Maxim Integrated Products, Inc.) 180mA, 1x/2x, White LED Charge Pump in 3mm x 3mm TDFN PDF资料下载
参数资料
| 型号： | MAX1574 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | 180mA, 1x/2x, White LED Charge Pump in 3mm x 3mm TDFN |
| 中文描述： | 180mA、1倍/2倍、白光LED电荷泵，3mm x 3mm TDFN封装 |
| 文件页数： | 6/9页 |
| 文件大小： | 214K |
| 代理商： | MAX1574 |
M
Detailed Description
The MAX1574 charge pump drives up to three white
LEDs with regulated constant current for uniform inten-
sity. By utilizing adaptive 1x/2x charge-pump modes
and very-low-dropout current regulators, it achieves
180mA output drive capability and high efficiency over
the 1-cell lithium-battery input voltage range. Fixed-fre-
quency switching of 1MHz allows for tiny external com-
ponents, and the regulation scheme is optimized to
ensure low EMI and low input ripple.
1x to 2x Switchover
When V
IN
is higher than V
OUT
, the MAX1574 operates in
1x mode and V
OUT
is pulled up to V
IN
. The internal cur-
rent regulators regulate the LED current. As V
IN
drops,
V
LED_
eventually falls below the switchover threshold of
130mV, and the MAX1574 starts switching in 2x mode.
When the input voltage rises above V
OUT
by approxi-
mately 50mV, the MAX1574 switches back to 1x mode.
Soft-Start
The MAX1574 includes soft-start circuitry to limit inrush
current at turn-on. When starting up, the output capacitor
is charged directly from the input with a ramped current
source (with no charge-pump action) until the output volt-
age approaches the input voltage. Once this occurs, the
charge pump determines if 1x or 2x mode is required. In
the case of 1x mode, the soft-start is terminated and nor-
mal operation begins. During the soft-start time, the out-
put current is set to 5% of the maximum set by R
SET
. In
the case of 2x mode, soft-start operates until the lowest of
LED1 to LED3 reaches regulation. If an overload condi-
tion occurs, soft-start repeats every 2.1ms. If the output is
shorted to ground, the output current is limited by the
MAX1574 switching technique.
Setting the Output Current
The LED current at full brightness is set by a resistor,
R
SET
, as follows:
EN Dimming Control
When the LEDs are enabled by driving EN high, the
MAX1574 goes through soft-start, bringing the LED cur-
rent up to I
LED_
. Dimming is then done by pulsing EN
low (500ns to 500μs pulse width). Each pulse reduces
the LED current by 10%, so after one pulse the LED cur-
rent is 0.9 x I
LED
. The tenth pulse reduces the current by
5%, so the I
LED_
current reduces from 0.1 x I
LED_
to 0.05
x I
LED
. The eleventh pulse sets the LED current back to
I
LED_
. Figure 1 shows a timing diagram for EN.
If dimming control is not required, EN works as a simple
on/off control. Drive EN high to enable the LEDs, or
drive EN low for shutdown.
Shutdown Mode
When EN is held low for 2ms or longer, the MAX1574
is shut down and put in a low-current mode. OUT is
internally pulled to GND with 5k
during shutdown.
Overvoltage Protection
If any LED fails as an open circuit, the output voltage is
limited to about 5V by gating on/off the charge pump.
If any LED_ is floating or grounded, the MAX1574 oper-
ates in the same overvoltage-protection mode. To avoid
overvoltage-protection mode when using fewer than
three LEDs, connect any unused LED_ to IN (Figure 3).
Thermal Shutdown
The MAX1574 includes a thermal-limit circuit that shuts
down the IC at approximately +160°C. The part turns on
after the IC cools by approximately 20°C.
R
V
I
LED
SET
.
×
_
=
0 6
393
180mA, 1x/2x, White LED Charge Pump
in 3mm x 3mm TDFN
6
_______________________________________________________________________________________
EN
I
LED_
SHDN
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
5%
100%90%
SHDN
2ms
(typ)
1
11
10
9
8
7
6
5
4
3
2
t
LO
t
HI
t
SHDN
≥
500ns
500ns TO 500
μ
s
0
t
SOFT-START
INITIAL t
HI
≥
50
μ
s
Figure 1. EN Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1576 | 480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash |
| MAX1576ETG | 480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash |
| MAX1577ZETA | 1.2A White LED Regulating Charge Pump for Camera Flashes and Movie Lights |
| MAX1577Y | CAP 10UF 50V ELECT TG SMD |
| MAX1577YETA | 1.2A White LED Regulating Charge Pump for Camera Flashes and Movie Lights |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1574EEE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1574ETB | 制造商:Maxim Integrated Products 功能描述:180MA, 1X/2X, WHITE LED CHARGE PUMP IN 3MM X - Rail/Tube |
| MAX1574ETB+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX1574ETB+T | 功能描述:LED照明驱动器 White LED 1x/2x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX1574ETB-T | 功能描述:LED照明驱动器 White LED 1x/2x Charge Pump RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。