- 您现在的位置：买卖IC网 > PDF目录383326 > MAX1578ETG (MAXIM INTEGRATED PRODUCTS INC) CAP 100UF 63V ELECT TG SMD PDF资料下载
参数资料
| 型号： | MAX1578ETG |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 显示驱动器 |
| 英文描述： | CAP 100UF 63V ELECT TG SMD |
| 中文描述： | LED DISPLAY DRIVER, QCC24 |
| 封装： | 4 X 4 MM, 0.80 MM HEIGHT, MO-220WGGD-2, TQFN-24 |
| 文件页数： | 9/13页 |
| 文件大小： | 221K |
| 代理商： | MAX1578ETG |
M
Complete Bias and White LED Power S upplies
for S mall T FT Displays
_______________________________________________________________________________________
9
Detailed Desc ription
Bias Power and UV LO
The MAX1578/MAX1579 contain an LED driver boost
converter and three charge pumps for LCD bias. The
undervoltage-lockout (UVLO) feature disables the LED
boost converter and the charge pumps when the input
voltage is below 2.35V (typ). Once V
IN
rises above
2.35V, and V
CTRL
and V
ONBIAS
are high, the boost
converter and charge pumps are enabled, respectively.
Charge-Pump Output S equenc ing
The outputs of the MAX1578/MAX1579 charge pumps
are sequenced to turn on and off in a predictable fash-
ion. The turn-on sequence is as follows (Figure 1):
1) When ONBIAS is high, the MAIN regulator (5V) is
enabled.
2) When V
MAIN
exceeds 4.6V, the NEG charge pump
(-10V) is enabled.
3) When V
NEG
reaches -8V, the POS charge pump
(+15V) is enabled.
The turn-off sequence is as follows (Figure 2):
1) When ONBIAS is driven low, the NEG charge pump
(-10V) is disabled.
2) Once V
NEG
is discharged to -0.87V, the POS charge
pump (+15V) is disabled.
3) Once V
POS
falls to 0.87V, the MAIN regulator (+5V)
is disabled and discharged.
MAIN Charge Pump
The MAX1578/MAX1579 include a charge pump that
uses two external capacitors to provide +5.5V output
(V
DD
) that is used to power the regulated LDO +5V out-
put (MAIN). The control logic configures the pump to
switch automatically between 1.5x and 2x modes to
maximize efficiency. If V
DD
exceeds 5.5V, the charge
pump stops switching. When ONBIAS is driven low,
V
DD
is connected to IN.
A low-dropout linear regulator regulates the output of
the main charge pump to +5V at MAIN. The MAIN out-
put is capable of sourcing as much as 25mA to an
external load and also supplies the POS and NEG
charge pumps. Drive ONBIAS low to disable the MAIN,
POS, and NEG outputs. During shutdown, MAIN is dis-
charged to GND with an internal 1k
resistor.
POS /NEG Charge Pumps
The MAX1578/MAX1579 include a positive and nega-
tive charge pump for LCD bias. The POS and NEG
charge pumps are powered from V
MAIN
. The POS and
NEG charge pumps operate at 15.6kHz with a 50%
duty cycle.
NEG Charge Pump (-10V S upply)
The NEG charge pump uses capacitors at CD1 and
CD2 to generate -10V (-2 x V
MAIN
). Connect 1μF ceram-
ic capacitors and 200
±5% resistors in series between
CD1 and PMP and between CD2 and PMPB. Drive
ONBIAS high to enable MAIN, NEG, and POS. During
shutdown, the NEG output is discharged to GND with an
internal 1.5k
resistor.
POS Charge Pump (+15V S upply)
The POS charge pump uses capacitors at CU1, CU2,
and CU3 to generate +15V (3 x V
MAIN
). Connect 1μF
ceramic capacitors between CU1 and PMP, between
CU2 and PMPB, and between CU3 and GND. Drive
ONBIAS high to enable MAIN, NEG, and POS. During
shutdown, POS is discharged to GND with an internal
3k
resistor.
LED Bac klighting Power
LED power is supplied by an internal MOSFET, 1MHz
boost converter. The boost converter is capable of dri-
ving up to 8 series LEDs at 25mA.
The output of the boost converter is regulated to main-
tain a constant voltage at CS, and therefore a constant
current through the LEDs. Once V
IN
is increased above
the UVLO voltage (2.35V) and V
CTRL
is above 0.17V,
the boost converter enters soft-start and charges the
output to its regulation voltage. An overvoltage-protec-
tion circuit shuts down the boost converter if V
OUT
exceeds 34V.
V
MAIN
(5V)
V
POS
(+15V)
V
NEG
(-10V)
ONBIAS
Figure 2. Charge-Pump Turn-Off Sequence
V
MAIN
(5V)
V
POS
(+15V)
V
NEG
(-10V)
ONBIAS
Figure 1. Charge-Pump Turn-On Sequence
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1579ETG | Complete Bias and White LED Power Supplies for Small TFT Displays |
| MAX1584 | 5-Channel Slim DSC Power Supplies |
| MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584-MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584ETJ | 5-Channel Slim DSC Power Supplies |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1578ETG+ | 功能描述:LED照明驱动器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX1578ETG+T | 功能描述:LED照明驱动器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX1578ETG-T | 功能描述:LED照明驱动器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX1579ETG | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX1579ETG+ | 功能描述:LED照明驱动器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。