- 您现在的位置：买卖IC网 > PDF目录16561 > MAX1579ETG+T (Maxim Integrated Products)IC PS BIAS/WHITE LED TFT 24-TQFN PDF资料下载
参数资料
| 型号： | MAX1579ETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC PS BIAS/WHITE LED TFT 24-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | LCD 显示器 |
| 电流 - 电源： | 3mA |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
Complete Bias and White LED Power Supplies
for Small TFT Displays
Detailed Description
Bias Power and UVLO
The MAX1578/MAX1579 contain an LED driver boost
converter and three charge pumps for LCD bias. The
undervoltage-lockout (UVLO) feature disables the LED
boost converter and the charge pumps when the input
voltage is below 2.35V (typ). Once V IN rises above
2.35V, and V CTRL and V ONBIAS are high, the boost
converter and charge pumps are enabled, respectively.
Charge-Pump Output Sequencing
The outputs of the MAX1578/MAX1579 charge pumps
are sequenced to turn on and off in a predictable fash-
ion. The turn-on sequence is as follows (Figure 1):
1) When ONBIAS is high, the MAIN regulator (5V) is
enabled.
2) When V MAIN exceeds 4.6V, the NEG charge pump
(-10V) is enabled.
3) When V NEG reaches -8V, the POS charge pump
(+15V) is enabled.
The turn-off sequence is as follows (Figure 2):
1) When ONBIAS is driven low, the NEG charge pump
(-10V) is disabled.
2) Once V NEG is discharged to -0.87V, the POS charge
pump (+15V) is disabled.
3) Once V POS falls to 0.87V, the MAIN regulator (+5V)
is disabled and discharged.
ONBIAS
V MAIN (5V)
V POS (+15V)
V NEG (-10V)
Figure 1. Charge-Pump Turn-On Sequence
ONBIAS
V MAIN (5V)
V POS (+15V)
V NEG (-10V)
Figure 2. Charge-Pump Turn-Off Sequence
MAIN Charge Pump
The MAX1578/MAX1579 include a charge pump that
uses two external capacitors to provide +5.5V output
(V DD ) that is used to power the regulated LDO +5V out-
put (MAIN). The control logic configures the pump to
switch automatically between 1.5x and 2x modes to
maximize efficiency. If V DD exceeds 5.5V, the charge
pump stops switching. When ONBIAS is driven low,
V DD is connected to IN.
A low-dropout linear regulator regulates the output of
the main charge pump to +5V at MAIN. The MAIN out-
put is capable of sourcing as much as 25mA to an
external load and also supplies the POS and NEG
charge pumps. Drive ONBIAS low to disable the MAIN,
POS, and NEG outputs. During shutdown, MAIN is dis-
charged to GND with an internal 1k Ω resistor.
POS/NEG Charge Pumps
The MAX1578/MAX1579 include a positive and nega-
tive charge pump for LCD bias. The POS and NEG
charge pumps are powered from V MAIN . The POS and
NEG charge pumps operate at 15.6kHz with a 50%
duty cycle.
NEG Charge Pump (-10V Supply)
The NEG charge pump uses capacitors at CD1 and
CD2 to generate -10V (-2 x V MAIN ). Connect 1μF ceram-
ic capacitors and 200 Ω ±5% resistors in series between
CD1 and PMP and between CD2 and PMPB. Drive
ONBIAS high to enable MAIN, NEG, and POS. During
shutdown, the NEG output is discharged to GND with an
internal 1.5k Ω resistor.
POS Charge Pump (+15V Supply)
The POS charge pump uses capacitors at CU1, CU2,
and CU3 to generate +15V (3 x V MAIN ). Connect 1μF
ceramic capacitors between CU1 and PMP, between
CU2 and PMPB, and between CU3 and GND. Drive
ONBIAS high to enable MAIN, NEG, and POS. During
shutdown, POS is discharged to GND with an internal
3k Ω resistor.
LED Backlighting Power
LED power is supplied by an internal MOSFET, 1MHz
boost converter. The boost converter is capable of dri-
ving up to 8 series LEDs at 25mA.
The output of the boost converter is regulated to main-
tain a constant voltage at CS, and therefore a constant
current through the LEDs. Once V IN is increased above
the UVLO voltage (2.35V) and V CTRL is above 0.17V,
the boost converter enters soft-start and charges the
output to its regulation voltage. An overvoltage-protec-
tion circuit shuts down the boost converter if V OUT
exceeds 34V.
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| EBC22DRXS-S734 | CONN EDGECARD 44POS DIP .100 SLD |
| H3CKH-4018G | IDC CABLE - HKC40H/AE40G/HPK40H |
| H3BWH-2618M | IDC CABLE - HSR26H/AE26M/HPL26H |
| MAX1578ETG+T | IC PS BIAS/WHITE LED TFT 24-TQFN |
| KSZ8721BL-EVAL | BOARD EVALUATION FOR KSZ8721BL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1579EVKIT | 功能描述:LED 照明开发工具 Evaluation Kit for the MAX1579 RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX157ACPA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX157ACPA+ | 功能描述:模数转换器 - ADC 10-Bit 2Ch 108ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX157ACUA | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX157ACUA+ | 功能描述:模数转换器 - ADC 10-Bit 2Ch 108ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。