参数资料
型号: MAX1583YETB+T
厂商: Maxim Integrated
文件页数: 8/10页
文件大小: 0K
描述: IC LED DRIVR PHOTO FLASH 10-TDFN
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 2,500
恒定电流:
拓扑: 升压(升压)
输出数: 1
内部驱动器:
类型 - 主要: 闪灯/白光
类型 - 次要: 白色 LED
频率: 750kHz ~ 1.25MHz
电源电压: 2.6 V ~ 5.5 V
输出电压: 24V
安装类型: 表面贴装
封装/外壳: 10-WFDFN 裸露焊盘
供应商设备封装: 10-TDFN-EP(3x3)
包装: 带卷 (TR)
工作温度: -40°C ~ 85°C
White LED Camera-Flash
Boost Converter
V IN
2.6V TO 5.5V
L1
4.7 μ H
2
IN
LX
10
D1
R3
100k Ω
C1
22 μ F
1
GND
MAX1583X
C2
10 μ F
D2, D3, D4
POWER-OK
5
POK
WHITE LEDs
6
EN1
OUT
8
MODE CONTROL
7
EN2
C3
0.1 μ F
R1
6.04k Ω
1%
R2
4
STB
LED
9
3.01k Ω
Figure 1. Typical Application Circuit
1%
3 MOV
C RES = LED BOOST STROBE
Design Procedure
Adjusting the LED Current
The LED current in the strobe and movie modes is pro-
grammable using external resistors. To set the LED cur-
rent during strobe mode, connect a resistor (R STB ) from
STB to GND. V STB is regulated to 0.6V and the current
sourced by STB is mirrored through LED with a gain of
1000. R STB is calculated as:
R STB = 600 / I LED(DESIRED)
To set the LED current during movie mode, connect a
resistor (R MOV ) from MOV to GND. V MOV is regulated
to 0.6V and the current sourced by MOV is mirrored
through LED with a gain of 100. R MOV is calculated as:
R MOV = 60 / I LED(DESIRED)
Reservoir Capacitance vs. Current Limit
During strobe mode, the current demands on the boost
converter to maintain the desired LED strobe current
may cause the MAX1583 to reach the preset current
limit. The MAX1583 is available with three factory-pre-
set current limits: 250mA, 500mA, and 1A. If the current
limit is reached, the internal MOSFET terminates its ON
cycle early, causing the output current to drop. See the
nect a reservoir capacitor from OUT to GND to provide
the extra LED current. The value of this capacitor is cal-
culated as:
( I ? I ) × t
24 V ? ( n × V F )
where:
I LED is the desired strobe current,
I BOOST is the maximum current from the boost convert-
er obtained from the Typical Operating Characteristics,
t STROBE is the time duration of the strobe,
n is the number of LEDs, and
V F is the forward voltage of the LEDs.
For example, assume a minimum input voltage of 3.2V
with the MAX1583Y (500mA current limit). The required
strobe current is 100mA for 30ms through two series
LEDs with a 4V forward voltage. The reservoir capacitor
is determined as follows:
I BOOST = 75mA from the Typical Operating
Characteristics .
Typical Operating Characteristics for the Maximum
Boost I OUT vs. V IN for each current limit. If the required
strobe current exceeds the maximum boost I OUT , con-
C RES =
( 100 mA ? 75 mA ) × 30 ms
24 V ? ( 2 × 4 V )
=
25 mA × 30 ms
16 V
= 47 μ F
8
_______________________________________________________________________________________
相关PDF资料
PDF描述
ECM06DRMH-S288 CONN EDGECARD 12POS .156 EXTEND
VI-J2M-CX-F1 CONVERTER MOD DC/DC 10V 75W
GCC12DCAT CONN EDGECARD 24POS R/A .100 SLD
VI-J2L-CX-F4 CONVERTER MOD DC/DC 28V 75W
MAX1583XETB+T IC LED DRIVR PHOTO FLASH 10-TDFN
相关代理商/技术参数
参数描述
MAX1583ZETB 制造商:Maxim Integrated Products 功能描述:WHITE LED CAMERA-FLASH BOOST CONVER - Rail/Tube
MAX1583ZETB+ 制造商:Maxim Integrated Products 功能描述:LED DRVR 5SEGMENT 2.6V TO 5.5V 10TDFN EP - Rail/Tube 制造商:Rochester Electronics LLC 功能描述:
MAX1583ZETB+T 功能描述:LED照明驱动器 White LED Camera Flash Boost Convertr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1583ZETB-T 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
MAX1584ETJ 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT