- 您现在的位置：买卖IC网 > PDF目录383327 > MAX1584-MAX1585 (Maxim Integrated Products, Inc.) 5-Channel Slim DSC Power Supplies PDF资料下载
参数资料
| 型号： | MAX1584-MAX1585 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | 5-Channel Slim DSC Power Supplies |
| 中文描述： | 5通道电源超薄数码相机 |
| 文件页数： | 12/29页 |
| 文件大小： | 632K |
| 代理商： | MAX1584-MAX1585 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
M
5-Channel Slim DSC Power Supplies
12
______________________________________________________________________________________
Detailed Description
The MAX1584/MAX1585 are complete power-conver-
sion ICs for slim digital still cameras. They can accept
input from a variety of sources, including single-cell Li+
batteries and 2-cell alkaline or NiMH batteries, as well
as systems designed to accept both battery types. The
MAX1584/MAX1585 include five DC-DC converter
channels to generate all required voltages (Figure 2
shows a functional diagram):
Synchronous-rectified step-up DC-DC converter with
on-chip MOSFETs
—
Typically supplies 3.3V for main
system power or 5V to power other DC-DC convert-
ers for boost-buck designs.
Synchronous-rectified step-down DC-DC converter
with on-chip MOSFETs
—
Typically supplies 1.8V for
the DSP core. Powering the step-down from the
step-up output provides efficient (up to 90%) boost-
buck functionality that supplies a regulated output
when the battery voltage is above or below the out-
put voltage. The step-down can also be powered
from the battery if there is sufficient headroom.
AUX1 step-up controller
—
Typically used for 15V to
bias one or more of the LCD, CCD, and LED back-
lights.
AUX2 step-up controller (MAX1584)
—
Typically sup-
plies remaining bias voltages with either a multi-out-
put flyback transformer or a boost converter with
charge-pump inverter. Alternately, can power white
LEDs for LCD backlighting.
AUX2 inverter controller (MAX1585)
—
Typically sup-
plies negative CCD bias when high current is need-
ed for large pixel-count CCDs.
AUX3 step-down controller
—
Typically steps 5V gen-
erated at PVSU down to 3.3V for system logic in
boost-buck designs.
Step-Up DC-DC Converter
The step-up DC-DC switching converter is typically used
to generate a 5V output voltage from a 1.5V to 4.5V bat-
tery input, but any voltage from V
IN
to 5V can be set. An
internal NFET switch and a PFET synchronous rectifier
allow conversion efficiencies as high as 95%. Under
moderate to heavy loading, the converter operates in a
low-noise PWM mode with constant frequency and modu-
lated pulse width. Switching harmonics generated by
fixed-frequency operation are consistent and easily fil-
tered. Efficiency is enhanced under light (<75mA typ)
loading, by an idle mode that switches the step-up only
as needed to service the load. In this mode, the maxi-
mum inductor current is 250mA for each pulse.
PIN
NAME
FUNCTION
28
DL3
AUX3 Step-Down Controller Gate-Drive Output. Connect to the gate of a P-channel MOSFET. DL3 swings
from GND to PVSU and supplies up to 500mA. DL3 is driven to PVSU in shutdown and thermal limit.
AUX1 Step-Up Controller Gate-Drive Output. Connect to the gate of an N-channel MOSFET. DL1 swings
from GND to PVSU and supplies up to 500mA. DL1 is driven to GND in shutdown and thermal limit.
Analog Ground. Connect to all PG_ pins as close to the IC as possible.
AUX3 Step-Down Controller Compensation Node. Connect a series resistor-capacitor from CC3 to FB3 to
compensate the converter control loop. This pin is actively driven to GND in shutdown, overload, and
thermal limit. See the
AUX Compensation
section.
PWM Step-Up Controller 3 Feedback Input. Connect a resistive voltage-divider from the output voltage to
FB3 to GND to set the output voltage. The FB3 feedback threshold is 1.25V. This pin is high impedance in
shutdown.
29
DL1
30
GND
31
CC3
32
FB3
PAD
EP
Exposed Underside Metal Pad. This pad must be soldered to the PC board to achieve package thermal
and mechanical ratings. There is no internal metal or bond wire physically connecting the exposed pad to
the GND pin(s). Connecting the exposed pad to ground does not remove the requirement for a good
ground connection to the appropriate IC pins.
Pin Description (continued)
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1584ETJ | 5-Channel Slim DSC Power Supplies |
| MAX1585ETJ | 5-Channel Slim DSC Power Supplies |
| MAX1586AETM | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1586 | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1587 | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1585ETJ | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1585ETJ+ | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1585ETJ+T | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1585ETJ-T | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1585EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX1585 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。