- 您现在的位置：买卖IC网 > PDF目录383326 > MAX1584 (Maxim Integrated Products, Inc.) 5-Channel Slim DSC Power Supplies PDF资料下载
参数资料
| 型号： | MAX1584 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | 5-Channel Slim DSC Power Supplies |
| 中文描述： | 5通道、纤小的DSC电源 |
| 文件页数： | 15/29页 |
| 文件大小： | 632K |
| 代理商： | MAX1584 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
M
5-Channel Slim DSC Power Supplies
______________________________________________________________________________________
15
Step-Down DC-DC Converter
The step-down DC-DC converter is optimized for gen-
erating low output voltages (down to 1.25V) at high effi-
ciency. Output voltages lower than 1V can be set by
adding an additional resistor (see the
Applications
Information
section). The step-down runs from the volt-
age at PVSD. This pin can be connected directly to the
battery if sufficient headroom exists to avoid dropout;
otherwise, PVSD can be powered from the output of
another converter. The step-down can also operate
with the step-up for boost-buck operation.
Under moderate to heavy loading, the converter oper-
ates in a low-noise PWM mode with constant frequency
and modulated pulse width. Efficiency is enhanced
under light (<75mA typ) loading by assuming an idle
mode during which the step-down switches only as
needed to service the load. In this mode, the maximum
inductor current is 100mA for each pulse. The step-
down DC-DC is inactive until the step-up DC-DC is in
regulation.
The step-down also features an open-drain
SDOK
out-
put that goes low when the step-down output is in regu-
lation.
SDOK
can be used to drive an external MOSFET
switch that gates 3.3V power to the processor after the
core voltage is in regulation. This connection is shown
in Figure 13.
Boost-Buck Operation
The step-down input can be powered from the output
of the step-up. By cascading these two channels, the
step-down output can maintain regulation even as the
battery voltage falls below the step-down output volt-
age. This is especially useful when trying to generate
3.3V from 1-cell Li+ inputs, or 2.5V from 2-cell alkaline
or NiMH inputs, or when designing a power supply that
must operate from both Li+ and alkaline/NiMH inputs.
Compound efficiencies of up to 90% can be achieved
when the step-up and step-down are operated in
series.
Note that the step-up output supplies both the step-up
load and the step-down input current when the step-
down is powered from the step-up. The step-down
input current reduces the available step-up output cur-
rent for other loads.
Direct Battery Step-Down Operation
The step-down converter can also be operated directly
from the battery as long as the voltage at PVSD does
not exceed PVSU by more than a Schottky diode for-
ward voltage. When using this connection, connect an
external Schottky diode from the battery input to PVSU.
On the MAX1584/MAX1585, there is an internal 10k
resistance from PVSU to PVSD. This adds a small addi-
tional current drain (of approximately (V
PVSU
- V
PVSD
) /
10k
) from PVSU when PVSD is not connected directly
to PVSU.
Step-down direct battery operation improves efficiency
for the step-down output (up to 95%), but restricts the
upper limit of the output voltage to 200mV less than the
minimum battery voltage. In 1-cell Li+ designs (with a
2.7V min), the output can be set up to 2.5V. In 2-cell
alkaline or NiMH designs, the output can be limited to
1.5V or 1.8V, depending on the minimum-allowed cell
voltage.
The step-down can only be briefly operated in dropout
since the MAX1584/MAX1585 fault protection detects
the out-of-regulation condition and activates after
100,000 OSC cycles (200ms at f
OSC
= 500kHz). At that
point, all MAX1584/MAX1585 channels shut down.
AUX1, AUX2, and AUX3 DC-DC Controllers
The three auxiliary controllers operate as fixed-frequen-
cy voltage-mode PWM controllers. They do not have
internal MOSFETs, so output power is determined by
external components. The controllers regulate output
voltage by modulating the pulse width of the DL_ drive
signal to an external MOSFET switch. The MAX1584
contains two step-up/flyback controllers (AUX1 and
AUX2) and one step-down controller (AUX3). The
MAX1585 contains one step-up controller (AUX1), one
inverting controller (AUX2), and one step-down con-
troller (AUX3).
Figure 3 shows a functional diagram of the AUX con-
trollers. The inverting and step-down controllers differ
from the step-up controllers only in the gate-drive logic
and FB polarity and threshold. The sawtooth oscillator
signal at OSC governs timing. At the start of each
cycle, DL_ turns on the external MOSFET switch. For
step-up controllers, DL_ goes high, while for inverting
and step-down controllers, DL_ goes low (to turn on
PFETs). The external MOSFET then turns off when the
internally level-shifted sawtooth rises above CC_ or
when the maximum duty cycle is exceeded. The switch
remains off until the start of the next cycle. A transcon-
ductance error amplifier forms an integrator at CC_ so
that high DC loop gain and accuracy can be main-
tained. In step-up and step-down controllers, the FB_
threshold is 1.25V, and higher FB_ voltages reduce the
MOSFET duty cycle. In inverting controllers, the FB_
threshold is 0V, and lower (more negative) FB_ volt-
ages reduce the MOSFET duty cycle.
Auxiliary controllers do not start until the step-up DC-DC
output is in regulation. If the step-up, step-down, or any
of the auxiliary controllers remains faulted for 100,000
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584-MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584ETJ | 5-Channel Slim DSC Power Supplies |
| MAX1585ETJ | 5-Channel Slim DSC Power Supplies |
| MAX1586AETM | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1584ETJ | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1584ETJ+ | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1584ETJ+T | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1584ETJ-T | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1585ETJ | 功能描述:直流/直流开关转换器 5Ch Slim DSC Power Supply RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。