- 您现在的位置：买卖IC网 > PDF目录16548 > MAX1586CETM+T (Maxim Integrated Products)IC POWER MANAGEMENT 48-TQFN PDF资料下载
参数资料
| 型号： | MAX1586CETM+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/30页 |
| 文件大小： | 0K |
| 描述： | IC POWER MANAGEMENT 48-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 手持/移动设备 |
| 电源电压： | 2.6 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-WFQFN 裸露焊盘 |
| 供应商设备封装： | 48-TQFN-EP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页
High-Efficiency, Low-I Q PMICs with
Dynamic Core for PDAs and Smart Phones
The LSB of the address word is the read/write (R/ W ) bit.
R/ W indicates whether the master is writing or reading
(RD/ W 0 = write, RD/ W 1 = read). The MAX1586/
MAX1587 only support the SEND BYTE format; there-
fore, RD/ W is required to be 0.
After receiving the proper address, the MAX1586/
MAX1587 issue an ACK by pulling SDA low for one
clock cycle. The MAX1586/MAX1587 have two user-
programmed addresses (Table 3). Address bits A7
through A2 are fixed, while A1 is controlled by SRAD.
Connecting SRAD to GND sets A1 = 0. Connecting
SRAD to IN sets A1 = 1.
V3 Output Ramp-Rate Control
When V3 is dynamically changed with the serial inter-
face, the output voltage changes at a rate controlled by
a capacitor (C RAMP ) connected from RAMP to ground.
The voltage change is a conventional RC exponential
described by:
Vo(t) = Vo(0) + dV(1 – exp(-t/(100k Ω C RAMP )))
A useful approximation is that it takes approximately 2.2
RC time constants for V3 to move from 10% to 90% of
the voltage difference. For C RAMP = 1500pF, this time
is 330μs. For 1V to 1.3V change, this equates to
1mV/μs. See the Typical Operating Characteristics for
examples of different ramp-rate settings.
The maximum capacitor value that can be used at
RAMP is 2200pF. If larger values are used, the V3 ramp
rate is still controlled according to the above equation,
but when V3 is first activated, POK indicates an “in reg-
ulation” condition before V3 reaches its final voltage.
The RAMP pin is effectively the reference for REG3.
FB3 regulates to 1.28 times the voltage on RAMP.
Design Procedure
Setting the Output Voltages
The outputs V1 and V2 have preset output voltages, but
can also be adjusted using a resistor voltage-divider. To
set V1 to 3.3V, connect FB1 to GND. V2 can be preset to
1.8V or 2.5V on the MAX1586A and MAX1587A. To set
V2 to 1.8V on the MAX1586A and MAX1587A, connect
FB2 to IN. To set to 2.5V, connect FB2 to GND. V2 can
preset to 3.3V or 2.5V on the MAX1587B. To set V2 to
3.3V on the MAX1587B, connect FB2 to IN. To set to
2.5V, connect FB2 to GND.
To set V1 or V2 to other than the preset output voltages,
connect a resistor voltage-divider from the output volt-
age to the corresponding FB input. The FB_ input bias
current is less than 100nA, so choose the low-side
(FB_-to-GND) resistor (R L ) to be 100k Ω or less. Then cal-
culate the high-side (output-to-FB_) resistor (R H ) using:
R H = R L [(V OUT /1.25) – 1]
The V3 (VCC_CORE) output voltage is set from 0.7V to
1.475V in 25mV steps by the I 2 C serial interface. See
the Serial Interface section for details.
Linear regulator V4 provides a fixed 1.3V output volt-
age. Linear regulator V5 provides a fixed 1.1V output
voltage. V4 and V5 voltages are not adjustable.
The output voltage of linear regulator V6 (VCC_USIM) is
set to 0V, 1.8V, 2.5V, or 3.0V by the I 2 C serial interface.
See the Serial Interface section for details.
Linear regulator V7 (VCC_BATT) tracks the voltage at
V1 as long as ON1 is high and V1 is in regulation. When
ON1 is low or V1 is not in regulation, V7 switches to the
backup battery (V BKBT ).
Inductor Selection
The external components required for the step-down
are an inductor, input and output filter capacitors, and a
compensation RC network.
The MAX1586/MAX1587 step-down converters provide
best efficiency with continuous inductor current. A rea-
sonable inductor value (L IDEAL ) is derived from:
L IDEAL = [2(V IN ) x D(1 - D)]/(I OUT(MAX) x f OSC )
This sets the peak-to-peak inductor current at 1/2 the
DC inductor current. D is the duty cycle:
D = V OUT / V IN
Given L IDEAL , the peak-to-peak inductor ripple current
is 0.5 x I OUT . The peak inductor current is 1.25 x
I OUT(MAX) . Make sure the saturation current of the
inductor exceeds the peak inductor current and the
rated maximum DC inductor current exceeds the maxi-
mum output current (I OUT(MAX) ). Inductance values
larger than L IDEAL can be used to optimize efficiency or
to obtain the maximum possible output current. Larger
inductance values accomplish this by supplying a
given load current with a lower inductor peak current.
Typically, output current and efficiency are improved
for inductor values up to about two times L IDEAL . If the
inductance is raised too much, however, the inductor
size may become too large, or the increased inductor
resistance may reduce efficiency more than the gain
derived from lower peak current.
Smaller inductance values allow smaller inductor sizes,
but also result in larger peak inductor current for a
given load. Larger output capacitance may then be
needed to suppress the increase in output ripple
caused by larger peak current.
Capacitor Selection
The input capacitor in a DC-DC converter reduces cur-
rent peaks drawn from the battery or other input power
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| HSM06DSEF | CONN EDGECARD 12POS .156 EYELET |
| MAX1586BETM+T | IC POWER MANAGEMENT 48-TQFN |
| MAX1586AETM+T | IC POWER MANAGEMENT 48-TQFN |
| HMM06DSEF | CONN EDGECARD 12POS .156 EYELET |
| HCM12DSAN | CONN EDGECARD 24POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1587AETL | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AETL+ | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AETL+T | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AETL-T | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AEVKIT | 功能描述:直流/直流开关转换器 MAX1587A Evaluation Kit/Evaluation System RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。