- 您现在的位置：买卖IC网 > PDF目录383327 > MAX1587AETL (MAXIM INTEGRATED PRODUCTS INC) High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones PDF资料下载
参数资料
| 型号： | MAX1587AETL |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC40 |
| 封装： | 6 X 6 MM, TQFN-40 |
| 文件页数： | 14/32页 |
| 文件大小： | 656K |
| 代理商： | MAX1587AETL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
M
High-Efficiency, Low-I
Q
PMICs with
Dynamic Core for PDAs and Smart Phones
14
______________________________________________________________________________________
Pin Description
PIN
MAX
1586
MAX
1587
NAME
FUNCTION
1
—
LBI
Dual-Mode, Low-Battery Input. Connect to IN to set the low-battery threshold to 3.6V (no resistors
needed). Connect LBI to a resistor-divider for an adjustable LBI threshold. When IN is below the set
threshold,
LBO
output switches low.
LBO
is deactivated and forced low when IN is below the dead-battery
(DBI) threshold and when all REGs are disabled.
2
40
CC1
REG1 Compensation Node. Connect a series resistor and capacitor from CC1 to GND to compensate the
regulation loop. See the
Compensation and Stability
section
.
3
1
FB1
REG1 Feedback Input. Connect to IN to set V1 to 3.0V or connect FB1 to GND to set V1 to 3.3V. Connect
FB1 to external feedback resistors for other output voltages.
4
2
BKBT
Input Connection for Backup Battery. This input can also accept the output of an external boost converter.
5
3
V7
Also known as VCC_BATT. V7 is always active if main or backup power is present. It is the first regulator
that powers up. V7 has two states:
1) V7 tracks V1 if ON1 is high and V1 is in regulation.
2) V7 tracks V
BKBT
when ON1 is low or V1 is out of regulation.
6
4
V1
REG1 Voltage-Sense Input. Connect directly to the REG1 output voltage. The output voltage is set by FB1
to either 3.0V, 3.3V, or adjustable with resistors.
7
5
SLPIN
Inp ut to V 1 and V 2 S eep Reg ul ator s. The i np ut to the stand b y r eg ul ator s at V 1 and V 2. C onnect S LP N to IN
8
6
V2
REG2 Voltage-Sense Input. Connect directly to the REG2 output voltage. The output voltage is set by FB2
to either 1.8V/2.5V (MAX1586A, MAX1587A), 3.3V/2.5V (MAX1586B), or adjustable with resistors.
9
7
FB2
REG2 Feedback Input. Connect to GND to set V2 to 2.5V on all devices. Connect FB2 to IN to set V2 to
1.8V on the MAX1586A and MAX1587A. Connect FB2 to IN to set V2 to 3.3V on the MAX1586B. Connect
FB2 to external feedback resistors for other voltages.
10
8
CC2
REG2 Compensation Node. Connect a series resistor and capacitor from CC2 to GND to compensate the
regulation loop. See the
Compensation and Stability
section.
11
9
POK
Power-OK Output. Open-drain output that is low when any of the V1–V6 outputs are below their regulation
threshold. When all activated outputs are in regulation, POK is high impedance. POK maintains a valid low
output with V7 as low as 1V. POK does not flag an out-of-regulation condition while REG3 is transitioning
between voltages set by serial programming. POK also does not flag for any REG channel that has been
turned off; however, if
all
REG channels are off (V1–V6), then POK is forced low. If IN < UVLO, then POK is
low. POK is expected to connect to nVCC_FAULT.
12
10
SCL
Serial Clock Input
13
11
SDA
Serial Data Input. Data is read on the rising edge of SCL. Serial data programs the REG3 (core) and REG6
(VCC_USIM) voltage. REG3 and REG6 can be programmed even when off, but at least one of the ON_ pins
must be logic-high to activate the serial interface. On power-up, REG3 defaults to 1.3V and REG6 defaults
to 0V.
14
12
PWM3
Force V3 to PWM at All Loads. Connect PWM3 to GND for normal operation (skip mode at light loads). Drive
or connect high for forced-PWM operation at all loads for V3 only.
15
—
LBO
Low-Battery Output. Open-drain output that goes low when IN is below the threshold set by LBI.
Dual Mode is a trademark of Maxim Integrated Products, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1586BETM | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1589A | Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN |
| MAX1589AETT | Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN |
| MAX1589AEZT | Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN |
| MAX1589EZT120-T | Low-Input-Voltage, 500mA LDO Regulator with RESETin SOT and TDFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1587AETL+ | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AETL+T | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AETL-T | 功能描述:直流/直流开关调节器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1587AEVKIT | 功能描述:直流/直流开关转换器 MAX1587A Evaluation Kit/Evaluation System RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1587AEVSYS | 功能描述:直流/直流开关转换器 High-Efficiency Low-IQ PMICs with Dynamic Core for PDAs and Smartphones RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。