- 您现在的位置：买卖IC网 > PDF目录13323 > MAX16006ATG+T (Maxim Integrated Products)IC UP SUPERVISOR OCTAL 24-TQFN PDF资料下载
参数资料
| 型号： | MAX16006ATG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/26页 |
| 文件大小： | 0K |
| 描述： | IC UP SUPERVISOR OCTAL 24-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 类型： | 多压监控器 |
| 监视电压数目： | 8 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 可调节/可选择 |
| 电压 - 阀值： | 8 种可选阀值组合 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
MAX16000–MAX16007
Low-Voltage, Quad-/Hex-/Octal-Voltage
μP Supervisors
Pin Description (MAX16000/MAX16001/MAX16002)
PIN
NAME
FUNCTION
1
2
3
4
5
6
7
8
9
10
11
12
1
2
4
5
6
7
10
11
12
14
15
16
1
2
4
5
—
—
8
—
—
10
11
12
IN3
IN4
GND
V CC
OUT3
OUT4
MARGIN
OUT2
OUT1
IN1
IN2
TOL
Monitored Input Voltage 3. See Table 1 for the input voltage threshold.
Monitored Input Voltage 4. See Table 1 for the input voltage threshold.
Ground
Unmonitored Power-Supply Input
Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the
voltage at IN3 exceeds its threshold. The open-drain output has a 30μA internal pullup to V CC .
Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the
voltage at IN4 exceeds its threshold. The open-drain output has a 30μA internal pullup to V CC .
Active-Low Manual Deassert Input. Pull MARGIN low to deassert all outputs (go into high state),
regardless of the voltage at any monitored input.
Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the
voltage at IN2 exceeds its threshold. The open-drain output has a 30μA internal pullup to V CC .
Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the
voltage at IN1 exceeds its threshold. The open-drain output has a 30μA internal pullup to V CC .
Monitored Input Voltage 1. See Table 1 for the input voltage threshold.
Monitored Input Voltage 2. See Table 1 for the input voltage threshold.
Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL
to V CC to select 10% threshold tolerance.
Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period,
RESET is asserted. The timer clears whenever a reset is asserted or a rising or falling edge on
WDI is detected. The watchdog timer enters a startup period that allows 54s for the first
—
3
3
WDI
transition to occur before a reset. Leave WDI unconnected to disable the watchdog timer. The
WDI open-state detector uses a small 400nA current. Therefore, do not connect WDI to anything
that will source or sink more than 200nA. Note that the leakage current specification for most
three-state drivers exceeds 200nA.
—
8
6
MR
Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the
reset timeout period after MR is deasserted. MR is pulled up to V CC through a 20k ? resistor.
Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period.
—
9
7
SRT
The reset timeout period can be calculated as follows:
Reset Timeout (s) = 2.06 x 10 6 ( ? ) x C SRT (F). For the internal timeout period of 140ms (min),
connect SRT to V CC .
Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its
—
13
9
RESET
respective threshold or MR is asserted. RESET remains asserted for the reset timeout period
after all monitored voltages exceed their respective thresholds and MR is deasserted. This
open-drain output has a 30μA internal pullup.
Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a
—
—
—
EP
low thermal resistance path from the IC junction to the PCB. Do not use as the electrical
connection to GND.
Maxim Integrated
7
相关PDF资料 |
PDF描述 |
|---|---|
| RBC50DREI-S13 | CONN EDGECARD 100PS .100 EXTEND |
| ACB30DHHD | CONN EDGECARD 60POS .050 DIP SLD |
| SC5040F-151 | INDUCTOR SMD 150UH 4.0A 100KHZ |
| SC5040F-150 | INDUCTOR SMD 15UH 13A 100KHZ |
| HMC18DRTN-S13 | CONN EDGECARD 36POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16006BTG | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, QUAD-/HEX-/OCTAL-VOLTAGE MICROPR - Rail/Tube |
| MAX16006BTG+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16006BTG+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16006BTG-T | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, QUAD-/HEX-/OCTAL-VOLTAGE MICROPR - Tape and Reel |
| MAX16006CTG | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE, QUAD-/HEX-/OCTAL-VOLTAGE MICROPR - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。