- 您现在的位置：买卖IC网 > PDF目录383327 > MAX1604EAI (MAXIM INTEGRATED PRODUCTS INC) Dual-Channel CardBus and PCMCIA Power Switches with SMBus⑩ Serial Interface PDF资料下载
参数资料
| 型号： | MAX1604EAI |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Dual-Channel CardBus and PCMCIA Power Switches with SMBus⑩ Serial Interface |
| 中文描述： | 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO28 |
| 封装： | 0.200 INCH, SSOP-28 |
| 文件页数： | 11/16页 |
| 文件大小： | 190K |
| 代理商： | MAX1604EAI |
M
Dual-Channel CardBus and PCMCIA
Power S witc hes with S MBus S erial Interfac e
______________________________________________________________________________________
11
_______________Detailed Desc ription
The MAX1601/MAX1604 power-switching ICs contain a
network of low-resistance MOSFET switches that deliver
selectable VCC and VPP voltages to two Cardbus or
PC Card host sockets. The MAX1601/MAX1604 differ
only in the VY switch on-resistance. Figure 1 is the
detailed block diagram.
The power-input pins (VY, VX, 12IN_) are completely
independent. Low inrush current is guaranteed by con-
trolled switch rise times. VCC’s 100μs minimum output
rise time is 100% tested with a 1μF capacitive load, and
VPP’s 1ms minimum rise time is guaranteed with a 0.1μF
load. These respective capacitive loads are chosen as
worst-case card-insertion parameters. The internal
switching control allows VCC and VPP rise times to be
controlled, and makes them nearly independent of resis-
tive and capacitive loads (see rise-time photos in the
Typical Operating Characteristics). Fall times are a
function of loading, and are compensated by internal
circuitry.
Power savings is automatic: internal charge pumps draw
very low current when the VCC switches are static.
Standby mode reduces switch supply current to 1μA.
Driving the VL pin low with an external logic gate (master
shutdown) reduces total supply current to1μA (Figure 2).
Operating Modes
The MAX1601/MAX1604 have three operating modes:
normal, standby, and shutdown. Normal mode supplies
the selected outputs with their appropriate supply volt-
ages. Standby mode places all switches at ground, high
impedance, or a combination of the two. Shutdown mode
turns all switches off, and puts the VCC and VPP outputs
into a high-impedance state. Pull VL low to enter shutdown
mode. To ensure a 0.05V/μs fall rate on VL, use a 1k
series resistor and a 0.1μF capacitor to ground (Figure 2).
Overc urrent Protec tion
Peak detecting circuitry protects both the VCC and
VPP switches against overcurrent conditions. When
current through any switch exceeds the internal current
limit (4A for VCC switches and 200mA for VPP switch-
es), the switch turns off briefly, then turns on again at
the controlled rise rate. If the overcurrent condition
lasts more than 2μs, the
SMBALERT
output latches
low. A continuous short-circuit condition results in a
pulsed output current until thermal shutdown is
reached.
SMBALERT
is open-drain and requires an
external pull-up resistor.
T hermal S hutdown
If the IC junction temperature rises above +150°C, the
thermal shutdown circuitry opens all switches, including
the GND switches, and
SMBALERT
is pulled low. When
the temperature falls below +130°C, the switches turn
on again at the controlled rise rate. If the overcurrent
condition remains, the part cycles between thermal
shutdown and overcurrent.
Undervoltage Loc kout
If the VX or VY switch input voltage drops below 1.5V,
the associated switch turns off and
SMBALERT
goes
low. For example, if VY is 3.3V and VX is 0V, and if the
interface controller selects VY, the VCCA output will be
3.3V. If VX is selected, VCCA changes to a high-imped-
ance output and
SMBALERT
goes low.
When a voltage is initially applied to 12IN_, it must be
greater than 8V to allow the switch to operate.
Operation continues until the voltage falls below 2V (the
VPP output is high impedance).
When VL drops to less than 2.3V, all switches are
turned off and the VCC and VPP outputs are high
impedance.
MAX1601
MAX1604
1k
0.1
μ
F
74HC04
MASTER
SHUTDOWN
VL
VY
VCCA
VPPA
3.3V
VPPB
VCCB
TO
SOCKETS
A AND B
Figure 2. Master Shutdown Circuit
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16037 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16033 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16034 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16035 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16036 | Low-Power Battery Backup Circuits in Small レDFN Packages |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1604EAI+ | 功能描述:电源开关 IC - 配电 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MAX1604EAI+T | 功能描述:电源开关 IC - 配电 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MAX1604EAI-T | 功能描述:电源开关 IC - 配电 RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| MAX16050ETI+ | 功能描述:监控电路 Volt Mtr/Sequencer w/Reverse-Seq RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16050ETI+T | 功能描述:监控电路 Volt Mtr/Sequencer w/Reverse-Seq RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。