- 您现在的位置：买卖IC网 > PDF目录383328 > MAX1605EUT-T (MAXIM INTEGRATED PRODUCTS INC) 30V Internal Switch LCD Bias Supply PDF资料下载
参数资料
| 型号： | MAX1605EUT-T |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | 30V Internal Switch LCD Bias Supply |
| 中文描述： | 0.58 A SWITCHING REGULATOR, 500 kHz SWITCHING FREQ-MAX, PDSO6 |
| 封装： | MO-170AB, SOT-23, 6 PIN |
| 文件页数： | 8/12页 |
| 文件大小： | 347K |
| 代理商： | MAX1605EUT-T |
M
30V Internal Switch LCD Bias Supply
8
_______________________________________________________________________________________
Design Procedure
Inductor Selection
Smaller inductance values typically offer smaller physi-
cal size for a given series resistance or saturation cur-
rent. Circuits using larger inductance values may start
up at lower input voltages and exhibit less ripple, but
also provide reduced output power. This occurs when
the inductance is sufficiently large to prevent the maxi-
mum current limit from being reached before the maxi-
mum on-time expires. The inductor
’
s saturation current
rating should be greater than the peak switching cur-
rent. However, it is generally acceptable to bias the
inductor into saturation by as much as 20%, although
this will slightly reduce efficiency.
Picking the Current Limit
The peak LX current limit (I
LX(MAX
)) required for the
application may be calculated from the following equa-
tion:
where t
OFF(MIN)
= 0.8μs, and V
IN(MIN)
is the minimum
voltage used to supply the inductor. The set current
limit must be greater than this calculated value. Select
the appropriate current limit by connecting LIM to V
CC
,
GND, or leaving it unconnected (see the
Current Limit
Select Pin (LIM)
section and Figure 2).
Diode Selection
The high maximum switching frequency of 500kHz
requires a high-speed rectifier. Schottky diodes, such as
the Motorola MBRS0530 or the Nihon EP05Q03L, are
recommended. To maintain high efficiency, the average
current rating of the Schottky diode should be greater
than the peak switching current. Choose a reverse
breakdown voltage greater than the output voltage.
Output Filter Capacitor
For most applications, use a small ceramic surface-
mount output capacitor, 1μF or greater. For small
ceramic capacitors, the output ripple voltage is domi-
nated by the capacitance value. If tantalum or elec-
trolytic capacitors are used, the higher ESR increases
the output ripple voltage. Decreasing the ESR reduces
the output ripple voltage and the peak-to-peak transient
voltage. Surface-mount capacitors are generally pre-
ferred because they lack the inductance and resis-
tance of their through-hole equivalents.
Input Bypass Capacitor
Two inputs, V
CC
and V
IN
, require bypass capacitors.
Bypass V
CC
with a 0.1μF ceramic capacitor as close to
the IC as possible. The input supplies high currents to
the inductor and requires local bulk bypassing close to
the inductor. A 10μF low-ESR surface-mount capacitor
is sufficient for most applications.
PC Board Layout and Grounding
Careful printed circuit layout is important for minimizing
ground bounce and noise. Keep the MAX1605
’
s
ground pin and the ground leads of the input and out-
put capacitors less than 0.2in (5mm) apart. In addition,
keep all connections to FB and LX as short as possible.
In particular, when using external feedback resistors,
locate them as close to FB as possible. To minimize
output voltage ripple, and to maximize output power
and efficiency, use a ground plane and solder GND
directly to the ground plane. Refer to the
MAX1605EVKIT evaluation kit for a layout example.
Applications Information
Negative Voltage for LCD Bias
The MAX1605 can also generate a negative output by
adding a diode-capacitor charge-pump circuit (D1, D2,
and C3) to the LX pin as shown in Figure 4. Feedback
is still connected to the positive output, which is not
loaded, allowing a very small capacitor value at C4. For
best stability and lowest ripple, the time constant of the
R1-R2 series combination and C4 should be near or
less than that of C2 and the effective load resistance.
Output load regulation of the negative output is some-
what looser than with the standard positive output cir-
cuit, and may rise at very light loads due to coupling
through the capacitance of D2. If this is objectionable,
reduce the resistance of R1 and R2, while maintaining
their ratio, to effectively preload the output with a few
hundred microamps. This is why the R1-R2 values
shown in Figure 3 are about 10-times lower than typical
values used for a positive-output design. When loaded,
the negative output voltage will be slightly lower (closer
to ground by approximately a diode forward voltage)
than the inverse of the voltage on C4.
Output Disconnected in Shutdown
When the MAX1605 is shut down, the output remains
connected to the input (Figure 3), so the output voltage
falls to approximately V
IN
- 0.6V (the input voltage
minus a diode drop). For applications that require out-
put isolation during shutdown, add an external PNP
transistor as shown in Figure 4. When the MAX1605 is
active, the voltage set at the transistor
’
s emitter
exceeds the input voltage, forcing the transistor into the
I
V
I
V
V
V
t
L
LX MAX
(
OUT
OUT MAX
(
IN MIN
(
OUT
IN MIN
(
2
OFF MIN
(
)
)
)
)
)
≥
×
+
(
)
×
×
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1605 | 30V Internal Switch LCD Bias Supply |
| MAX160MJN | ; External Depth:125mm; External Width:45mm; Length/Height, External:68mm; Power Rating:4kW RoHS Compliant: Yes |
| MAX160-MX7574 | 10 AMP MINIATURE POWER RELAY |
| MAX160EWN | レP Compatible 8 Bit A/D Converter |
| MAX7574KN | BCD-to-Decimal Decoders/Drivers 16-CDIP -55 to 125 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1605EUTTG16 | 制造商:Maxim Integrated Products 功能描述:30V Internal Switch LCD Bias Supply |
| MAX1605EVKIT | 功能描述:直流/直流开关转换器 Evaluation Kit for the MAX1605 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX16060ATE+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16060ATE+T | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MAX16060BTE+ | 功能描述:监控电路 Quad/Hex/Octal Volt uP Supervisor RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。