- 您现在的位置：买卖IC网 > PDF目录14487 > MAX1623EAP+ (Maxim Integrated Products)IC REG BUCK SYNC ADJ 3A 20SSOP PDF资料下载
参数资料
| 型号： | MAX1623EAP+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 20SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 66 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.1 V ~ 3.8 V |
| 输入电压： | 4.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 最高 350kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 20-SSOP |
| 产品目录页面： | 1410 (CN2011-ZH PDF) |
3A, Low-Voltage, Step-Down Regulator with
Synchronous Rectification and Internal Switches
f = desired switching frequency during continuous
inductor current
LX
MAX1623
PGND
GND
FB
R1 = 10k ? to 500k ?
R2 = R1(V OUT / V REF - 1)
V REF = 1.1V
Figure 3. Adjustable Output Voltage
R2
R1
V OUT
V PCH = the voltage drop across the internal P-channel
switch
V NCH = the voltage drop across the internal N-channel
synchronous rectifier
Switching frequency decreases as load current is
decreased below the 625mA Idle Mode trip point.
Internal Reference
The 1.10V internal reference (available at REF) is accu-
rate to ±1.5% over the -40°C to +85°C operating range,
making it useful as a precision system reference. Bypass
the reference to ground with a minimum 0.1μF ceramic
capacitor. For low noise and jitter performance, use a
0.47μF ceramic capacitor. The reference can supply up
A high capacitor value maintains a constant average
output voltage but slows the loop response to changes
in output voltage. A low capacitor value speeds up the
loop response to changes in output voltage. Choose
the capacitor value that results in optimal performance.
Current Limiting
The current-sense circuit enables when the PMOS
power switch is on. This circuit’s corresponding output
voltage feeds three separate comparators: the skip cur-
rent comparator (1.25A), the maximum current com-
parator (4.15A), and the PWM current comparator (see
the Modes of Operation section).
Oscillator Frequency and
Programming the Off-Time
The MAX1623 features a programmable off-time that is
set by R TOFF connected from TOFF to GND. Connecting
a 110k ? resistor from TOFF to GND achieves a 1μs
(nominal) off-time. The off-time is inversely proportional
to R TOFF according to the formula:
t OFF = R TOFF / 110k (μs)
t OFF is adjustable between 0.5μs to 4μs (see the
Typical Operating Characteristics ). To set the switching
frequency when the inductor operates in continuous-
conduction mode, the off-time has to be set to:
to 10μA for external loads. However, if tight accuracy
specifications for either reference or the main output are
essential, avoid reference loads in excess of 5μA.
Loading the reference reduces the main output voltage
slightly, according to the reference-voltage load-regula-
tion error.
Start-Up
To prevent the MAX1623 from false output regulation,
the internal PMOS and NMOS switches will not switch
on until all of the following conditions are true: the sup-
ply voltage is above the undervoltage lockout thresh-
old, SHDN is pulled high, the internal reference voltage
is at 75% of its nominal (1.1V) value, and the die tem-
perature is below +145°C. When the above conditions
are satisfied, the MAX1623 will regulate the output volt-
age to the selected level. The MAX1623 typically starts
up in 1ms for full output load.
Thermal Shutdown and
Overload Conditions
Thermal overload protection limits the MAX1623’s total
power dissipation. When the junction temperature
reaches T j = +145°C, the device turns off, allowing it to
cool down. Switching resumes after the IC’s junction
temperature decreases by 20°C. If the thermal overload
condition persists, the output pulses on and off.
t OFF =
V I
f ( V I
? V O ?
? V PCH
V PCH
+ V NCH )
Thermal overload protection is designed to protect the
MAX1623 during fault conditions, such as an output
short circuit.
where:
t OFF = the programmed off-time
V I = input voltage
V O = output voltage
Thermal Resistance
Junction to ambient thermal resistance ( θ JA ) strongly
depends on the amount of copper area immediately
surrounding the IC’s leads. The MAX1623 evaluation kit
has 0.8in 2 of copper area. θ JA on this board was mea-
sured to have 45°C/W of thermal resistance with no air
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| HSC07DREF-S734 | CONN EDGECARD 14POS .100 EYELET |
| MAX743CWE+ | IC REG BOOST INV 125MA DL 16SOIC |
| LGN2H151MELC25 | CAP ALUM 150UF 500V 20% SNAP |
| HMC07DREF-S734 | CONN EDGECARD 14POS .100 EYELET |
| VI-B1B-EW-F2 | CONVERTER MOD DC/DC 95V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1623EAP+ | 功能描述:直流/直流开关调节器 3A Step-Down w/Synch Rectification RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EAP+T | 功能描述:直流/直流开关调节器 3A Step-Down w/Synch Rectification RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EAP-T | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EVKIT | 功能描述:直流/直流开关调节器 Evaluation Kit for the MAX1623 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1624EAG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。