- 您现在的位置：买卖IC网 > PDF目录1838 > MAX1623EAP (Maxim Integrated Products)IC REG BUCK SYNC ADJ 3A 20SSOP PDF资料下载
参数资料
| 型号： | MAX1623EAP |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 3A 20SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 66 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.1 V ~ 3.8 V |
| 输入电压： | 4.5 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 最高 350kHz |
| 电流 - 输出： | 3A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 20-SSOP |
3A, Low-Voltage, Step-Down Regulator with
Synchronous Rectification and Internal Switches
flow. A copper area of 0.4in 2 showed thermal resis-
tance of 60°C/W.
Airflow over the IC can significantly reduce θ JA .
Table 2. Suggested Values (V IN = 5V,
I O = 3A, f = 300kHz)
Power Dissipation
The MAX1623’s power dissipation consists mostly of con-
duction losses in the two internal power switches. Power
dissipation due to supply current in the control section
and average current used to charge and discharge the
gate capacitance of the two power switches is less than
30mW at 300kHz. This number is reduced when switch-
ing frequency is reduced as the part enters Idle Mode.
Combined conduction loss in the two power switches is
V OUT
(V)
3.3
2.5
1.8
1.5
1.1
T OFF
(μs)
1.10
1.67
2.16
2.38
2.68
R TOFF
(k ? )
120
180
240
260
280
L
(μH)
4.7
4.7
4.7
3.9
3.3
calculated by:
P D = I LOAD2 (R ON )
where R ON = 100m ? (max).
The θ JA required to deliver this amount of power is cal-
The peak inductor current at full load is 1.15 x I OUT if
the above equation is used; otherwise, the peak current
can be calculated by:
culated by:
where:
θ JA = (T J(MAX) – T A(MAX) ) / P D
I PEAK = I OUT +
V OUT (V IN(MAX) ? V OUT )
2 × f × L × V IN(MAX)
) ? ?
(
I RIPPLE = I LOAD ?
?
?
T J(MAX) = maximum allowed junction temperature
T A(MAX) = maximum ambient temperature expected
Applications Information
Inductor L1
The inductor value can be adjusted to optimize the
design for size, cost, and efficiency. Three key inductor
parameters must be specified: inductance value (L),
peak current (I PEAK ), and DC resistance (R DC ). The fol-
lowing equation includes a constant, denoted as LIR,
which is the ratio of inductor peak-to-peak AC current
to DC load current. A higher value of LIR allows smaller
inductance, but results in higher losses and ripple. A
good compromise between size and losses is found at
a 30% ripple current to load current ratio (LIR = 0.3),
which corresponds to a peak inductor current 1.15
times the DC load current:
The inductor’s DC resistance is a key parameter for effi-
ciency and must be minimized, preferably to less than
25m ? at I OUT = 3A. To reduce EMI, use a shielded
inductor.
Input and Output Filter
Capacitors (C1, C2)
Use a low-ESR input capacitor according to the input
ripple-current requirements and voltage rating.
? V OUT V IN ? V OUT
? V IN ?
In addition to C1, place a 10μF ceramic bypass capacitor
from the power input (pin 2, 4, 6) to power ground (pin
15, 17, 19) within 5mm of the IC.
The output filter capacitor determines the output volt-
L =
V IN(MAX) × f × (I OUT ) (LIR)
V OUT (V IN(MAX) ? V OUT )
age ripple and output load-transient response, as well
as the loop’s stability.
The output ripple in continuous-conduction mode is:
V OUT(RPL) OUT(MAX) × LIR ? ESR C2 +
= I
?
where:
f = switching frequency
I OUT = maximum DC load current
LIR = ratio of AC to DC inductor current, typically
?
?
where f is the switching frequency.
1 ?
2 π × f × C2 ?
0.3
10 _______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1626ESA-T | IC REG CTRLR BUCK PWM CM 8-SOIC |
| MAX1631EAI | IC REG CTRLR BUCK PWM CM 28-SSOP |
| MAX1634AEAI+ | IC REG CTRLR BUCK PWM CM 28-SSOP |
| MAX1636EAP+T | IC REG CTRLR BUCK PWM CM 20-SSOP |
| MAX1637EEE | IC REG CTRLR BUCK PWM CM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1623EA-P | 制造商:Maxim Integrated Products 功能描述: |
| MAX1623EAP+ | 功能描述:直流/直流开关调节器 3A Step-Down w/Synch Rectification RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EAP+T | 功能描述:直流/直流开关调节器 3A Step-Down w/Synch Rectification RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EAP-T | 功能描述:直流/直流开关调节器 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MAX1623EVKIT | 功能描述:直流/直流开关调节器 Evaluation Kit for the MAX1623 RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。