- 您现在的位置：买卖IC网 > PDF目录15041 > MAX1627ESA (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 8-SOIC PDF资料下载
参数资料
| 型号： | MAX1627ESA |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/16页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 300kHz |
| 占空比： | 100% |
| 电源电压： | 3 V ~ 16.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
5V/3.3V or Adjustable, 100% Duty-Cycle,
High-Efficiency, Step-Down DC-DC Controllers
With high inductor values, the MAX1626/MAX1627 will
begin continuous-conduction operation at a lower frac-
tion of the full load (see Detailed Description). Low-value
inductors may be smaller and less expensive, but they
result in greater peak current overshoot due to current-
sense comparator propagation delay. Peak-current
overshoot reduces efficiency and could cause the exter-
nal components’ current ratings to be exceeded.
The inductor’s saturation and heating current ratings
must be greater than the peak switching current to pre-
vent overheating and core saturation. Saturation occurs
when the inductor’s magnetic flux density reaches the
maximum level the core can support, and inductance
starts to fall. The heating current rating is the maximum
DC current the inductor can sustain without overheating.
The peak switching current is the sum of the current limit
set by the current-sense resistor and overshoot during
current-sense comparator propagation delay.
or shielded-core inductor to minimize radiated noise.
Table 1 lists inductor types and suppliers for various
applications.
External Switching Transistor
The MAX1626/MAX1627 drive P-channel enhancement-
mode MOSFETs. The EXT output swings from GND to
the voltage at V+. To ensure the MOSFET is fully on,
use logic-level or low-threshold MOSFETs when the
input voltage is less than 8V. Tables 1 and 2 list recom-
mended suppliers of switching transistors.
Four important parameters for selecting a P-channel
MOSFET are drain-to-source breakdown voltage, cur-
rent rating, total gate charge (Q g ), and R DS(ON) . The
drain-to-source breakdown voltage rating should be at
least a few volts higher than V+. Choose a MOSFET
with a maximum continuous drain current rating higher
than the peak current limit:
I PEAK =
V CS
R CS
+
( V + ? V OUT ) × 1 μ s
L
I D(MAX ) ≥ I LIM ( MAX ) =
V CS ( MAX )
R SENSE
1μs is the worst-case current-sense comparator propa-
gation delay.
Inductors with a core of ferrite, Kool Mu?, METGLAS?,
or equivalent, are recommended. Powder iron cores
are not recommended for use with high switching
frequencies. For optimum efficiency, the inductor wind-
ings’ resistance should be on the order of the current-
sense resistance. If necessary, use a toroid, pot-core,
KOOL Mu is a trademark of Magnetics.
METGLAS is a trademark of Allied Signal.
Table 1. Component Selection Guide
The Qg specification should be less than 100nC to
ensure fast drain voltage rise and fall times, and reduce
power losses during transition through the linear region.
Q g specifies all of the capacitances associated with
charging the MOSFET gate. EXT pin rise and fall times
vary with different capacitive loads, as shown in the
Typical Operating Characteristics. R DS(ON) should be
as low as practical to reduce power losses while the
MOSFET is on. It should be equal to or less than the
current-sense resistor.
PRODUCTION
METHOD
Surface Mount
INDUCTORS
Sumida
CDRH125-470 (1.8A)
CDRH125-220 (2.2A)
CoilCraft
DO3316-473 (1.6A)
DO3340-473 (3.8A)
CAPACITORS
AVX
TPS series
Sprague
595D series
DIODES
Motorola
MBRS340T3
Nihon
NSQ series
CURRENT-SENSE
RESISTORS
Dale
WSL series
IRC
LRC series
MOSFETS
Siliconix
Little Foot series
Motorola
medium-power
surface-mount products
Sanyo
Miniature
Through-Hole
Sumida
RCH875-470M (1.3A)
OS-CON series
low-ESR organic
IRC
OAR series
Motorola
semiconductor
Nichicon
Motorola
United Chemi-Con
Low-Cost
Through-Hole
CoilCraft
PCH-45-473 (3.4A)
PL series
low-ESR electrolytics 1N5817 to
1N5823
Motorola
TMOS power MOSFETs
LXF series
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 380LX121M315H022 | CAP ALUM 120UF 315V 20% SNAP |
| ESRD221M0EXR | CAP ALUM 220UF 2.5V 20% SMD |
| VE-20Y-EY-F2 | CONVERTER MOD DC/DC 3.3V 33W |
| ESRD680M08B | CAP ALUM 68UF 8V 20% SMD |
| VE-20Y-EY-F1 | CONVERTER MOD DC/DC 3.3V 33W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1627ESA+ | 功能描述:DC/DC 开关控制器 5/3.3V or Adjustable 100% Duty Cycle RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1627ESA+ | 制造商:Maxim Integrated Products 功能描述:CONTROLLER STEP DOWN DC-DC 1627 制造商:Maxim Integrated Products 功能描述:CONTROLLER, STEP DOWN, DC-DC, 1627 |
| MAX1627ESA+G071 | 功能描述:DC/DC 开关控制器 Adjustable 100% Duty-Cycle High-Efficiency Step-Down DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1627ESA+T | 功能描述:DC/DC 开关控制器 5/3.3V or Adjustable 100% Duty Cycle RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1627ESA+TG071 | 功能描述:DC/DC 开关控制器 5V/3.3V or Adjustable 100% Duty Cycle High-Efficiency Step-Down DC-DC Controllers RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。