- 您现在的位置：买卖IC网 > PDF目录15138 > MAX1634AEAI+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 28-SSOP PDF资料下载
参数资料
| 型号： | MAX1634AEAI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/29页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 28-SSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 2 |
| 频率 - 最大： | 330kHz |
| 占空比： | 99% |
| 电源电压： | 4.2 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 28-SSOP（0.209"，5.30mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
Current-Sense Resistor Value
The current-sense resistor value is calculated according
to the worst-case-low current-limit threshold voltage
(from the Electrical Characteristics table) and the peak
inductor current:
Output Filter Capacitor Value
The output filter capacitor values are generally deter-
mined by the ESR and voltage rating requirements, rather
than actual capacitance requirements for loop stability. In
other words, the low-ESR electrolytic capacitor that meets
R SENSE =
80mV
I PEAK
the ESR requirement usually has more output capaci-
tance than is required for AC stability. Use only special-
ized low-ESR capacitors intended for switching-regulator
Use I PEAK from the second equation in the Inductor
Value section
Use the calculated value of R SENSE to size the MOSFET
switches and specify inductor saturation-current ratings
according to the worst-case high-current-limit threshold
voltage:
applications, such as AVX TPS, Sprague 595D, Sanyo
OS-CON, or Nichicon PL series. To ensure stability, the
capacitor must meet both minimum capacitance and
maximum ESR values as given in the following equations:
V REF (1 + V OUT / V IN(MIN) )
C OUT >
V OUT x R SENSE x f
I PEAK(MAX) =
120mV
R SENSE
R ESR <
R SENSE x V OUT
V REF
I RMS = LOAD
Low-inductance resistors, such as surface-mount
metal-film, are recommended.
Input Capacitor Value
Connect low-ESR bulk capacitors and small ceramic
capacitors (0.1μF) directly to the drains on the high-side
MOSFETs. The bulk input filter capacitor is usually
selected according to input ripple current requirements
and voltage rating, rather than capacitor value.
Electrolytic capacitors with low enough effective series
resistance (ESR) to meet the ripple current requirement
invariably have sufficient capacitance values. Aluminum
electrolytic capacitors, such as Sanyo
OS-CON or Nichicon PL, are superior to tantalum types,
which carry the risk of power-up surge-current failure,
especially when connecting to robust AC adapters or
low-impedance batteries. RMS input ripple current
(I RMS ) is determined by the input voltage and load cur-
rent, with the worst case occurring at V IN = 2 x V OUT :
V OUT (V IN - V OUT )
I RMS = I LOAD x
V IN
Therefore , when V IN is 2 X V OUT :
I
2
Bypassing V+
Bypass the V+ input with a 4.7μF tantalum capacitor
paralleled with a 0.1μF ceramic capacitor, close to the
IC. A 10 Ω series resistor to V IN is also recommended.
Bypassing VL
Bypass the VL output with a 4.7μF tantalum capacitor
paralleled with a 0.1μF ceramic capacitor, close to the
device.
(can be multiplied by 1.5; see text below)
These equations are worst case, with 45 degrees of
phase margin to ensure jitter-free, fixed-frequency
operation and provide a nicely damped output
response for zero to full-load step changes. Some cost-
conscious designers may wish to bend these rules with
less-expensive capacitors, particularly if the load lacks
large step changes. This practice is tolerable if some
bench testing over temperature is done to verify
acceptable noise and transient response.
No well-defined boundary exists between stable and
unstable operation. As phase margin is reduced, the
first symptom is a bit of timing jitter, which shows up as
blurred edges in the switching waveforms where the
scope does not quite sync up. Technically speaking,
this jitter (usually harmless) is unstable operation, since
the duty factor varies slightly. As capacitors with higher
ESRs are used, the jitter becomes more pronounced,
and the load-transient output voltage waveform starts
looking ragged at the edges. Eventually, the load-tran-
sient waveform has enough ringing on it that the peak
noise levels exceed the allowable output voltage toler-
ance. Note that even with zero phase margin and gross
instability present, the output voltage noise never gets
much worse than I PEAK x R ESR (under constant loads).
Designers of RF communicators or other noise-sensi-
tive analog equipment should be conservative and stay
within the guidelines. Designers of notebook computers
and similar commercial-temperature-range digital
systems can multiply the R ESR value by a factor of 1.5
without hurting stability or transient response.
The output voltage ripple is usually dominated by the
filter capacitor’s ESR, and can be approximated as
I RIPPLE x R ESR . There is also a capacitive term, so the
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| SLP681M160C5P3 | CAP ALUM 680UF 160V 20% SNAP |
| EMC15DRAS | CONN EDGECARD 30POS R/A .100 SLD |
| MAX1717BEEG+T | IC REG CTRLR BUCK PWM CM 24-QSOP |
| UCD2A151MNQ1MS | CAP ALUM 150UF 100V 20% SMD |
| GBB15DHAS | CONN EDGECARD 30POS R/A .050 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1634CAI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1634CAI+ | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1634CAI+T | 功能描述:DC/DC 开关控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1634CAI-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1634EAI | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。