- 您现在的位置：买卖IC网 > PDF目录1838 > MAX1636EAP+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 20-SSOP PDF资料下载
参数资料
| 型号： | MAX1636EAP+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/23页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 20-SSOP |
| 标准包装： | 2,000 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 99% |
| 电源电压： | 3.15 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 带卷 (TR) |
Low-Voltage, Precision Step-Down
Controller for Portable CPU Power
Table 6. Low-Voltage Troubleshooting Chart
SYMPTOM
CONDITION
ROOT CAUSE
SOLUTION
Increase bulk output capacitance
Sag or droop in V OUT under
step-load change
Low V IN -V OUT
differential, <1.5V
Limited inductor-current
slew rate per cycle.
per formula (see Low-Voltage
Operation section). Reduce inductor
value.
Dropout voltage is too high
(V OUT follows V IN as V IN
decreases)
Unstable—jitters between
different duty factors and
frequencies
Poor efficiency
Won’t start under load or
quits before battery is
completely dead
Low V IN -V OUT
differential, <1V
Low V IN -V OUT
differential, <0.5V
Low input voltage, <5V
Low input voltage, <4.5V
Maximum duty-cycle limits
exceeded.
Normal function of internal
low-dropout circuitry.
VL linear regulator is going
into dropout and isn’t provid-
ing good gate-drive levels.
VL output is so low that it
hits the VL UVLO threshold.
Reduce operation to 200kHz.
Reduce MOSFET on-resistance and
coil DCR.
Increase the minimum input voltage
or ignore.
Use a small 20mA Schottky diode
for boost diode. Supply VL from an
external source.
Supply VL from an external source
other than V IN , such as the system
+5V supply.
where R DC is the DC resistance of the coil, R DS(ON) is
the MOSFET on-resistance, and R SENSE is the current-
sense resistor value. The R DS(ON) term assumes identi-
cal MOSFETs for the high-side and low-side switches
because they time-share the inductor current. If the
MOSFETs are not identical, their losses can be estimat-
ed by averaging the losses according to duty factor.
PD(tran) = transition loss = V IN x I LOAD x f x 3/2 x
[(V IN C RSS / I GATE ) + 20ns]
where C RSS is the reverse transfer capacitance of the
high-side MOSFET (a data-sheet parameter), I GATE is
the DH gate-driver peak output current (1.5A typ), and
20ns is the rise/fall time of the DH driver (20ns typ).
P(gate) = Q g x f x VL
where VL is the internal logic-supply voltage (+5V), and
Q g is the sum of the gate-charge values for low-side
and high-side switches. For matched MOSFETs, Q g is
twice the data-sheet value of an individual MOSFET. If
V OUT is set to less than 4.5V, replace VL in this equa-
tion with V BATT . In this case, efficiency can be
improved by connecting VL to an efficient 5V source,
such as the system +5V supply.
P(diode) = diode conduction losses =
I LOAD x V FWD x t D x f
where t D is the diode-conduction time (120ns typ), and
V FWD is the forward voltage of the diode. This power is
dissipated in the MOSFET body diode if no external
Schottky diode is used.
P(cap) = input capacitor ESR loss = I RMS2 x R ESR
where I RMS is the input ripple current as calculated in
the Input Capacitor Value section.
Light-Load Efficiency Considerations
Under light loads, the PWM operates in discontinuous
mode, where the inductor current discharges to zero at
some point during the switching cycle. This makes the
inductor current’s AC component high compared to the
load current, which increases core losses and I 2 R loss-
es in the output filter capacitors. For best light-load effi-
ciency, use MOSFETs with moderate gate-charge
levels and use ferrite, MPP, or other low-loss core mate-
rial. Avoid powdered-iron cores; even Kool-Mu
(aluminum alloy) is not as good as ferrite.
PC Board Layout Considerations
Good PC board layout is required in order to achieve
specified noise, efficiency, and stable performance.
The PC board layout artist must be given explicit
instructions, preferably a pencil sketch showing the
placement of power-switching components and high-
current routing. See the PC board layout in the
MAX1636 evaluation kit manual for examples. A ground
plane is essential for optimum performance. In most
applications, the circuit will be located on a multi-layer
board, and full use of the four or more copper layers
is recommended. Use the top layer for high-current
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1637EEE | IC REG CTRLR BUCK PWM CM 16-QSOP |
| MAX1638EAG+T | IC STEP-DWN CTRLR HI-SPD 24-SSOP |
| MAX1639ESE+T | IC REG CTRLR BUCK PWM CM 16-SOIC |
| MAX1641EEE+ | IC SW-MODE CUR SOURCE ADJ 16QSOP |
| MAX1644EAE-T | IC REG BUCK SYNC ADJ 2A 16SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1637EEE | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EEE+ | 功能描述:DC/DC 开关控制器 Mini Precision Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EEE+T | 功能描述:DC/DC 开关控制器 Mini Precision Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EEE-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1637EVKIT | 制造商:Maxim Integrated Products 功能描述:MINIATURE, LOW-VOLTAGE, PRECISION STEP-DOWN C - Bulk |
发布紧急采购，3分钟左右您将得到回复。