- 您现在的位置：买卖IC网 > PDF目录15139 > MAX1637EEE+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1637EEE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 1 |
| 频率 - 最大： | 338kHz |
| 占空比： | 96% |
| 电源电压： | 3.15 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
Miniature, Low-Voltage,
Precision Step-Down Controller
Inductor Value
The exact inductor value is not critical and can be
freely adjusted to allow trade-offs among size, cost,
and efficiency. Lower inductor values minimize size
and cost, but reduce efficiency due to higher peak-
current levels. The smallest inductor value is obtained
by lowering the inductance until the circuit operates at
the border between continuous and discontinuous
mode. Further reducing the inductor value below this
crossover point results in discontinuous-conduction
operation, even at full load. This helps lower output filter
capacitance requirements, but efficiency suffers under
these conditions, due to high I 2 R losses. On the other
hand, higher inductor values produce greater efficien-
cy, but also result in resistive losses due to extra wire
turns—a consequence that eventually overshadows the
benefits gained from lower peak current levels. High
inductor values can also affect load-transient response
(see the V SAG equation in the Low-Voltage Operation
section). The equations in this section are for continu-
ous-conduction operation.
Three key inductor parameters must be specified:
inductance value (L), peak current (I PEAK ), and DC
resistance (R DC ). The following equation includes a
constant, LIR, which is the ratio of inductor peak-to-
peak AC current to DC load current. A higher LIR value
allows lower inductance, but results in higher losses
and ripple. A good compromise is a 30% ripple-current
to load-current ratio (LIR = 0.3), which corresponds to a
peak inductor current 1.15 times higher than the DC
load current.
L = V OUT (V IN(MAX) - V OUT ) / (V IN(MIN) x ? x I OUT x
LIR)
where ? = switching frequency (normally 200kHz or
300kHz), and I OUT = maximum DC load current.
The peak current can be calculated as follows:
I PEAK = I LOAD + [V OUT (V IN(MAX) - V OUT ) / (2 x ? x L
x V IN(MAX) )]
The inductor’s DC resistance should be low enough
that R DC x I PEAK < 100mV, as it is a key parameter for
efficiency performance. If a standard, off-the-shelf
inductor is not available, choose a core with an LI 2 rat-
ing greater than L x IPEAK 2 and wind it with the largest
diameter wire that fits the winding area. For 300kHz
applications, ferrite-core material is strongly preferred;
for 200kHz applications, Kool-Mu ? (aluminum alloy) or
even powdered iron is acceptable. If light-load efficien-
cy is unimportant (in desktop PC applications, for
example), then low-permeability iron-powder cores can
Kool-Mu is a trademark of Magnetics, Inc.
be acceptable, even at 300kHz. For high-current appli-
cations, shielded-core geometries (such as toroidal or
pot core) help keep noise, EMI, and switching-
waveform jitter low.
Current-Sense Resistor Value
The current-sense resistor value is calculated accord-
ing to the worst-case, low-current limit threshold volt-
age (from the Electrical Characteristics ) and the peak
inductor current:
R SENSE = 80mV / I PEAK
Use I PEAK from the second equation in the Inductor
Value section. Use the calculated value of R SENSE to
size the MOSFET switches and specify inductor satura-
tion-current ratings according to the worst-case high-
current-limit threshold voltage:
I PEAK = 120mV / R SENSE
Low-inductance resistors, such as surface-mount metal
film, are recommended.
Input Capacitor Value
Connect low-ESR bulk capacitors directly to the drain
on the high-side MOSFET. The bulk input filter capaci-
tor is usually selected according to input ripple current
requirements and voltage rating, rather than capacitor
value. Electrolytic capacitors with low enough equiva-
lent series resistance (ESR) to meet the ripple-current
requirement invariably have sufficient capacitance val-
ues. Aluminum electrolytic capacitors, such as Sanyo
OS-CON or Nichicon PL, are superior to tantalum
types, which risk power-up surge-current failure, espe-
cially when connecting to robust AC adapters or low-
impedance batteries. RMS input ripple current (I RMS ) is
determined by the input voltage and load current, with
the worst case occurring at V IN = 2 x V OUT . Therefore,
when V IN is 2 x V OUT :
I RMS = I LOAD / 2
V CC and V GG should be isolated from each other with a
20 Ω resistor and bypassed to ground independently.
Place a 0.1μF capacitor between V CC and GND, as
close to the supply pin as possible. A 4.7μF capacitor
is recommended between V GG and PGND.
Output Filter Capacitor Value
The output filter capacitor values are generally deter-
mined by the ESR and voltage-rating requirements,
rather than by actual capacitance requirements for loop
stability. In other words, the low-ESR electrolytic capac-
itor that meets the ESR requirement usually has more
output capacitance than is required for AC stability.
______________________________________________________________________________________
15
相关PDF资料 |
PDF描述 |
|---|---|
| GSM18DTMI-S189 | CONN EDGECARD 36POS R/A .156 SLD |
| CAT1021LI-42-G | IC SUPERVISR CPU 2K EEPROM 8PDIP |
| CAT1021LI-45-G | IC SUPERVISR CPU 2K EEPROM 8PDIP |
| MAX5060ATI+T | IC REG CTRLR BUCK PWM CM 28-TQFN |
| CAT1022LI-30-G | IC SUPERVISR CPU 2K EEPROM 8PDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1637EVKIT | 制造商:Maxim Integrated Products 功能描述:MINIATURE, LOW-VOLTAGE, PRECISION STEP-DOWN C - Bulk |
| MAX1638BEAG | 制造商:MAX 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1638EAG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1638EAG+ | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1638EAG+T | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。