- 您现在的位置：买卖IC网 > PDF目录383329 > MAX1639ESE (MAXIM INTEGRATED PRODUCTS INC) High-Speed Step-Down Controller with Synchronous Rectification for CPU Power PDF资料下载
参数资料
| 型号： | MAX1639ESE |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 稳压器 |
| 英文描述： | High-Speed Step-Down Controller with Synchronous Rectification for CPU Power |
| 中文描述： | SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | SOIC-16 |
| 文件页数： | 10/13页 |
| 文件大小： | 108K |
| 代理商： | MAX1639ESE |
Overvoltage Protec tion
When the output exceeds the set voltage, the synchro-
nous rectifier output (DL) is driven high (and DH is dri-
ven low). This causes the inductor to quickly dissipate
any stored energy and force the fault current to flow to
ground. Current is limited by the source impedance
and parasitic resistance of the current path, so a fuse is
required in series with the +5V input to protect against
low-impedance faults, such as a shorted high-side
MOSFET. Otherwise, the low-side MOSFET will eventu-
ally fail. DL will go low if the input voltage drops below
the undervoltage lockout point.
Internal S oft-S tart
Soft-start allows a gradual increase of the internal cur-
rent limit at start-up to reduce input surge currents. An
internal DAC raises the current-limit threshold from 0V
to 100mV in four steps (25mV, 50mV, 75mV, and
100mV) over the span of 1536 oscillator cycles.
__________________Design Proc edure
S etting the Output V oltage
Set the output voltage by connecting R7 and R8 (Figure 6)
to the FB pin from the output to AGND. R7 is given by the
following equation:
where V
FB
= 1.1V. Since the input bias current at FB
has a maximum value of ±0.1μA, values up to 10k
can be used for R8 with no significant accuracy loss.
Values under 1k
are recommended to improve noise
immunity. Place R7 and R8 very close to the MAX1639,
within 0.2in (5mm) of the FB pin.
Feed-Forward Compensation
An optional compensation capacitor (C8), typically
220pF, may be needed across the upper feedback
resistor to counter the effects of stray capacitance on the
FB pin, and to help ensure stable operation when high-
value feedback resistors are used (Figure 6). Empirically
adjust the feed-forward capacitor as needed.
S pec ifying the Induc tor
Three key inductor parameters must be specified:
inductance value (L), peak current (I
PEAK
), and DC
resistance (R
DC
). The following equation includes a
constant LIR, which is the ratio of inductor peak-to-
peak AC current to DC load current. Typically LIR can
be between 0.1 to 0.5. A higher LIR value allows for
smaller inductors and better transient response, but
results in higher losses and output ripple. A good com-
promise between size and loss is a 30% ripple current
to load current ratio (LIR = 0.30), which corresponds to
a peak inductor current 1.15 times higher than the DC
load current.
R
R
x
V
V
OUT
FB
7
8
1
=
M
High-S peed S tep-Down Controller with
S ync hronous Rec tific ation for CPU Power
10
______________________________________________________________________________________
C10
4.7nF
R1
C9
4.7nF
R9
39
R5
10
R10
39
CSH
V
CC
CSL
MAX1639
N1
C5
0.1
μ
F
C6
10
μ
F
C1
V
IN
Figure 5. High-Side Current Sense
R8
PLACE VERY CLOSE
TOMAX1639
R7
FB
AGND
V
OUT
C8 (OPTIONAL)
LOAD
MAX1639
Figure 6. Output Selection
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1639 | High-Speed Step-Down Controller with Synchronous Rectification for CPU Power |
| MAX1640C | Adjustable-Output, Switch-Mode Current Sources with Synchronous Rectifier |
| MAX1640 | Adjustable-Output, Switch-Mode Current Sources with Synchronous Rectifier |
| MAX1640EEE | Adjustable-Output, Switch-Mode Current Sources with Synchronous Rectifier |
| MAX1640D | Adjustable-Output, Switch-Mode Current Sources with Synchronous Rectifier |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1639ESE+ | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639ESE+T | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639ESE-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit the MAX1639 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX163BCNG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。