- 您现在的位置：买卖IC网 > PDF目录1838 > MAX1641EEE+ (Maxim Integrated Products)IC SW-MODE CUR SOURCE ADJ 16QSOP PDF资料下载
参数资料
| 型号： | MAX1641EEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC SW-MODE CUR SOURCE ADJ 16QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 充电管理 |
| 电源电压： | 5.5 V ~ 26 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
MAX1640/MAX1641
Adjustable-Output, Switch-Mode
Current Source with Synchronous Rectifier
where V TERM = 2V and V OUT is the desired output
voltage.
Programming the Off-Time
When programming the off-time, consider such factors
as maximum inductor current ripple, maximum output
voltage, inductor value, and inductor current rating. The
output current ripple is less than the inductor current rip-
ple and depends heavily on the output capacitor’s size.
Perform the following steps to program the off-time:
1) Select the maximum output current ripple. I R (A)
generating increased ripple at the output. Select C CC
to optimize the ripple vs. loop response.
Synchronous Rectification
Synchronous rectification reduces conduction losses in
the rectifier by shunting the Schottky diode with a low-
resistance MOSFET switch. In turn, efficiency increases
by about 3% to 5% at heavy loads. To prevent cross-
conduction or “shoot-through,” the synchronous rectifier
turns on shortly after the P-channel power MOSFET
Table 2. Component Manufacturers
2) Select the maximum output voltage. V OUT (MAX)(V)
3) Calculate the inductor value range as follows:
COMPONENT
Sumida
MANUFACTURER
CDRH125 series
t OFF =
L MIN = (V OUTMAX x 1μs) / I R
L MAX = (V OUTMAX x 10μs) / I R
4) Select an inductor value in this range.
5) Calculate t OFF as follows:
L x I R
V OUTMAX
6) Program t OFF by selecting R TOFF from:
R TOFF = (29.3 x 10 9 ) x t OFF
Inductor
MOSFETs
Sense Resistor
Capacitors
Rectifier
Coilcraft
Coiltronics
International Rectifier
Siliconix
Dale
IRC
AVX
Sprague
Motorola
Nihon
D03316P series
UP2 series
IRF7309
S14539DY
WSL-2010 series
LR2010-01 series
TPS series
595D series
MBAR5340t3
IN5817-IN5822
NSQ03A04
7) Calculate the switching frequency by:
fs = 1 / (t ON + t OFF )
where t ON = (I R x L) / (V IN - V OUT ) and I R = (V OUT x
t OFF ) / L. L is the inductor value, V IN is the input volt-
age, V OUT is the output voltage, and I R is the output
peak-to-peak current ripple.
Note that R TOFF sets both the off-time and the pulse-
trickle charge period.
Reference
The on-chip reference is laser trimmed for a precise 2V
at REF. REF can source no more than 50μA. Bypass
REF with a 0.1μF capacitor to ground.
Constant-Current Loop: AC Loop
Compensation
The constant-current loop’s output is brought out at CC.
To reduce noise due to variations in switching currents,
bypass CC with a 1nF to 100nF capacitor to ground. A
large capacitor value maintains a constant average out-
put current but slows the loop response to changes in
switching current. A small capacitor value speeds up
the loop response to changes in switching current,
Maxim Integrated
turns off. The synchronous rectifier remains off for 90%
of the off-time. In low-cost designs, the synchronous
rectifier FET may be replaced by a Schottky diode.
Component Selection
External Switching Transistors
The MAX1640/MAX1641 drive an enhancement-mode
P-channel MOSFET and a synchronous-rectifier N-
channel MOSFET (Table 2).
When selecting a P-channel FET, some important para-
meters to consider are on-resistance (r DS(ON) ), maxi-
mum drain-to-source voltage (V DS max), maximum
gate-to-source voltage (V GS max), and minimum
threshold voltage (V TH min).
In high-current applications, MOSFET package power
dissipation often becomes a dominant design factor.
I2R power losses are the greatest heat contributor for
both high-side and low-side MOSFETs. Switching loss-
es affect the upper MOSFET only (P-channel), since the
Schottky rectifier or the N-FET body diode clamps the
switching node before the synchronous rectifier turns on.
9
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1644EAE-T | IC REG BUCK SYNC ADJ 2A 16SSOP |
| MAX1651CSA | IC REG CTRLR BUCK PWM 8-SOIC |
| MAX1653EEE-T | IC REG CTRLR BUCK PWM CM 16-QSOP |
| MAX1659ESA+ | IC REG LDO 5V/ADJ .35A 8-SOIC |
| MAX1667EAP+T | IC SMART BATT CHGR LEVEL2 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1641EEE+ | 功能描述:电流型 PWM 控制器 Adj-Out Switch Mode Current Source RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1641EEE+T | 功能描述:电流型 PWM 控制器 Adj-Out Switch Mode Current Source RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1641EEE-T | 功能描述:电流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| MAX1642EUA | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1642EUA+ | 功能描述:直流/直流开关转换器 Integrated Circuits (ICs) RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。