- 您现在的位置：买卖IC网 > PDF目录15147 > MAX1649CSA+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM 8-SOIC PDF资料下载
参数资料
| 型号： | MAX1649CSA+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 8-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 控制器 |
| 输出数： | 1 |
| 频率 - 最大： | 300kHz |
| 占空比： | 96.5% |
| 电源电压： | 3 V ~ 16 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
5V/3.3V or Adjustable, High-Efficiency,
Low-Dropout, Step-Down DC-DC Controllers
To maximize efficiency and reduce the size and cost
of external components, minimize the peak current.
However, since the available output current is a func-
tion of the peak current, the peak current must not be
too low.
To choose the proper current-sense resistor for a par-
ticular output voltage, determine the minimum input
voltage and the maximum load current. Next, refer-
ring to Figures 5a or 5b, using the minimum input volt-
age, find the curve with the largest sense resistor that
provides sufficient output current. It is not necessary
to perform worst-case calculations. These curves take
into account the sense-resistor (±5%) and inductor
(47μH ±10%) values, the diode drop (0.4), and the
IC’s current-sense trip level (85mV); an external MOS-
FET on-resistance of 0.07 Ω is assumed for V GS = -5V.
Standard wire-wound and metal-film resistors have an
inductance high enough to degrade performance.
Surface-mount (chip) resistors have very little inductance
and are well suited for use as current-sense resistors.
A U-shaped wire resistor made by IRC works well in
through-hole applications. Because this resistor is a
band of metal shaped as a “U”, its inductance is less
than 10nH (an order of magnitude less than metal film
resistors). Resistance values between 5m Ω and 0.1 Ω
are available (see Table 1).
Inductor Selection
The MAX1649/MAX1651 operate with a wide range of
inductor values, although for most applications coils
between 10μH and 68μH take best advantage of the con-
trollers’ high switching frequency. With a high inductor
value, the MAX1649/MAX1651 will begin continuous-cur-
rent operation (see Detailed Description ) at a lower frac-
tion of full-load current. In general, smaller values pro-
duce higher ripple (see below) while larger values require
larger size for a given current rating.
In both the continuous and discontinuous modes, the
lower limit of the inductor is important. With a too-small
inductor value, the current rises faster and overshoots the
desired peak current limit because the current-limit com-
parator has a finite response time (300ns). This reduces
efficiency and, more importantly, could cause the current
rating of the external components to be exceeded.
Calculate the minimum inductor value as follows:
(V+(max) - V OUT ) x 0.3μs
L(min) = ——————————––——
Δ I x I LIM
where Δ I is the inductor-current overshoot factor,
I LIM = V CS /R SENSE , and 0.3μs is the time it takes the com-
parator to switch. Set Δ I = 0.1 for an overshoot of 10%.
For highest efficiency, use a coil with low DC resis-
tance; a value smaller than 0.1V/I LIM works best. To
minimize radiated noise, use a toroid, pot core, or
shielded-bobbin inductor. Inductors with a ferrite core
or equivalent are recommended. Make sure the induc-
tor’s saturation-current rating is greater than I LIM (max).
However, it is generally acceptable to bias the inductor
into saturation by about 20% (the point where the
inductance is 20% below its nominal value).
3.0
2.5
2.0
1.5
1.0
0.5
0
V OUT = 5V
r s = 0.030
r s = 0.040
r s = 0.050
r s = 0.060
r s = 0.080
r s = 0.100
3.0
2.5
2.0
1.5
1.0
0.5
0
V OUT = 3.3V
r s = 0.030
r s = 0.040
r s = 0.050
r s = 0.060
r s = 0.080
r s = 0.100
5.0
5.4
5.8
6.2
6.6
16.0
3.0
3.4
3.8
4.2
4.6
16.0
INPUT VOLTAGE (V)
Figure 5a. MAX1649 Current-Sense Resistor Graph
INPUT VOLTAGE (V)
Figure 5b. MAX1651 Current-Sense Resistor Graph
_______________________________________________________________________________________
9
相关PDF资料 |
PDF描述 |
|---|---|
| ISL88013IH529Z-TK | IC VOLTAGE MONITOR DUAL SOT23-5 |
| MAX16955AUE/V+T | IC REG CTRLR BUCK PWM CM 16TSSOP |
| MAX1771CSA+T | IC REG CTRLR BST PWM 8-SOIC |
| ISL88013IH526Z-TK | IC VOLTAGE MONITOR DUAL SOT23-5 |
| ISL88013IH523Z-TK | IC VOLTAGE MONITOR DUAL SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1649EPA | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1649EPA+ | 功能描述:DC/DC 开关控制器 3V or Adjustable High-Efficiency Low-Dropout Step-Down DC-DC Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1649ESA | 功能描述:DC/DC 开关控制器 5/3.3/Adj Low-Drop Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1649ESA+ | 功能描述:DC/DC 开关控制器 5/3.3/Adj Low-Drop Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1649ESA+T | 功能描述:DC/DC 开关控制器 5/3.3/Adj Low-Drop Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。