- 您现在的位置：买卖IC网 > PDF目录15140 > MAX1652EEE+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1652EEE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 20/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| PWM 型： | 电流模式，混合 |
| 输出数： | 2 |
| 频率 - 最大： | 350kHz |
| 占空比： | 98% |
| 电源电压： | 4.5 V ~ 30 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页
High-Efficiency, PWM, Step-Down
DC-DC Controllers in 16-Pin QSOP
__________________Design Procedure
The predesigned standard application circuits (Figure
1 and Table 1) contain ready-to-use solutions for com-
mon applications. Use the following design procedure
to optimize the basic schematic for different voltage or
current requirements. Before beginning a design, firmly
establish the following:
V IN(MAX) , the maximum input (battery) voltage. This
value should include the worst-case conditions, such
as no-load operation when a battery charger or AC
adapter is connected but no battery is installed.
V IN(MAX) must not exceed 30V. This 30V upper limit is
determined by the breakdown voltage of the BST float-
ing gate driver to GND (36V absolute maximum).
V IN(MIN) , the minimum input (battery) voltage. This
should be at full-load under the lowest battery condi-
tions. If V IN(MIN) is less than 4.5V, a special circuit must
AC current to DC load current. A higher value of LIR
allows smaller inductance, but results in higher losses
and ripple. A good compromise between size and loss-
es is found at a 30% ripple current to load current ratio
(LIR = 0.3), which corresponds to a peak inductor cur-
rent 1.15 times higher than the DC load current.
V OUT (V IN(MAX) - V OUT )
L = ———————————
V IN(MAX) x f x I OUT x LIR
where: f = switching frequency, normally 150kHz or
300kHz
I OUT = maximum DC load current
LIR = ratio of AC to DC inductor current,
typically 0.3
The peak inductor current at full load is 1.15 x I OUT if
the above equation is used; otherwise, the peak current
can be calculated by:
be used to externally hold up VL above 4.8V. If the min-
imum input-output difference is less than 1V, the filter
capacitance required to maintain good AC load regula-
I PEAK = I LOAD +
V OUT (V IN(MAX) - V OUT )
2 x f x L x V IN ( MAX )
tion increases.
Inductor Value
The exact inductor value isn ’t critical and can be
adjusted freely in order to make trade-offs among size,
cost, and efficiency. Although lower inductor values will
minimize size and cost, they will also reduce efficiency
due to higher peak currents. To permit use of the physi-
cally smallest inductor, lower the inductance until the
circuit is operating at the border between continuous
and discontinuous modes. Reducing the inductor value
even further, below this crossover point, results in dis-
continuous-conduction operation even at full load. This
helps reduce output filter capacitance requirements but
causes the core energy storage requirements to
increase again. On the other hand, higher inductor val-
ues will increase efficiency, but at some point resistive
losses due to extra turns of wire will exceed the benefit
gained from lower AC current levels. Also, high induc-
tor values affect load-transient response; see the V SAG
equation in the Low-Voltage Operation section.
The following equations are given for continuous-conduc-
tion operation since the MAX1652 family is mainly intend-
ed for high-efficiency, battery-powered applications. See
Appendix A in Maxim’s Battery Management and DC-DC
Converter Circuit Collection for crossover point and dis-
continuous-mode equations. Discontinuous conduction
doesn’t affect normal Idle Mode operation.
Three key inductor parameters must be specified:
inductance value (L), peak current (I PEAK ), and DC
resistance (R DC ). The following equation includes a
constant LIR, which is the ratio of inductor peak-to-peak
The inductor’s DC resistance is a key parameter for effi-
ciency performance and must be ruthlessly minimized,
preferably to less than 25m ? at I OUT = 3A. If a stan-
dard off-the-shelf inductor is not available, choose a
core with an LI 2 rating greater than L x I PEAK2 and wind
it with the largest diameter wire that fits the winding
area. For 300kHz applications, ferrite core material is
strongly preferred; for 150kHz applications, Kool-mu
(aluminum alloy) and even powdered iron can be
acceptable. If light-load efficiency is unimportant (in
desktop 5V-to-3V applications, for example) then low-
permeability iron-powder cores may be acceptable,
even at 300kHz. For high-current applications, shielded
core geometries (such as toroidal or pot core) help
keep noise, EMI, and switching-waveform jitter low.
Current-Sense Resistor Value
The current-sense resistor value is calculated accord-
ing to the worst-case, low-current-limit threshold voltage
(from the Electrical Characteristics table) and the peak
inductor current. The continuous-mode peak inductor-
current calculations that follow are also useful for sizing
the switches and specifying the inductor-current satu-
ration ratings. In order to simplify the calculation, I LOAD
may be used in place of I PEAK if the inductor value has
been set for LIR = 0.3 or less (high inductor values)
and 300kHz operation is selected. Low-inductance
resistors, such as surface-mount metal-film resistors,
are preferred.
80mV
R SENSE = ————
I PEAK
20
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1654EEE+ | IC REG CTRLR BUCK PWM CM 16-QSOP |
| MAX1744AUB/V+T | IC REG CTRLR BUCK PWM 10-UMAX |
| B82498F3279M | INDUCTOR 2.7NH 1000MA 0805 20% |
| TVX0J332MCD | CAP ALUM 3300UF 6.3V 20% AXIAL |
| MAX1775EEE+T | IC REG CTRLR BUCK PWM 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1652EEE+ | 功能描述:DC/DC 开关控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1652EEE+T | 功能描述:DC/DC 开关控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1652EEE-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1653EEE | 功能描述:DC/DC 开关控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1653EEE+ | 功能描述:DC/DC 开关控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。