- 您现在的位置：买卖IC网 > PDF目录20752 > MAX16800ATE/V+T (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 16-TQFN PDF资料下载
参数资料
| 型号： | MAX16800ATE/V+T |
| 厂商： | Maxim Integrated |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR HIGH BRIGHT 16-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 拓扑： | 线性（LDO），PWM |
| 输出数： | 1 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 电源电压： | 6.5 V ~ 40 V |
| 输出电压： | 5.27V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-WQFN 裸露焊盘 |
| 供应商设备封装： | 16-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
High-Voltage, 350mA, Adjustable Linear
High-Brightness LED (HB LED) Driver
power series pass device (see the Functional
Diagram). The regulation point is factory set at (V CS+ -
V CS- ) = 204mV ±3.5%. The regulated current is user
defined by the value of R SENSE .
The MAX16800 is a current controller internally opti-
mized for driving the impedance range expected from
one or more HB LEDs.
+5V Regulator
The MAX16800 includes a fixed +5V output regulator
that delivers up to 4mA of load current for low-power
applications throughout the +6.5V to +40V input volt-
age range. Connect a 0.1μF compensation capacitor
from V5 to ground. Shorting V5 to ground disables the
thermal shutdown.
Thermal Protection
The MAX16800 enters a thermal-shutdown mode in the
event of overheating. This typically occurs in overload or
output short-circuit conditions. When the junction tem-
perature exceeds T J = +155°C (typ), the internal ther-
mal-protection circuitry turns off the series pass device.
The MAX16800 recovers from thermal-shutdown mode
once the junction temperature drops by 23°C (typ). The
part will therefore protect itself by thermally cycling in the
event of a short-circuit or overload condition.
Applications Information
Programming the LED Current
The MAX16800 uses a sense resistor across CS+ and
CS- to set the LED current. The differential sense ampli-
V EN
fier connected across R SENSE provides ground-loop
immunity and low-frequency noise rejection. The LED
current is given by the equation below:
I LED = V SENSE / R SENSE
Input Voltage Considerations
For proper operation, the minimum input voltage must
always be +1.2V (+1.5V for V IN <+12V) higher than the
worst-case sum of all the forward drops of all series-
connected LEDs to the output of the MAX16800. The
minimum operating voltage of the device is +6.5V. The
device will operate below +6.5V; however, output cur-
rent may not meet the full regulation specification (see
the Typical Operating Characteristics).
Low-Frequency PWM at the Output
The MAX16800 provides pulsed or chopped current
dimming. Generally, high-brightness LEDs are binned
to match at their full-rated current; however, LEDs from
the same bin exhibit poor matching at currents other
than full-rated current. To achieve uniformity, HB LED
manufacturers recommend PWM pulsing of the LED
current at their full-rated value. There are two methods
for producing a PWM output. One method is by pulsing
the enable input (EN) while having a constant voltage
at IN. The other method is to connect EN to IN and
pulse both EN and IN. Both methods generate a regu-
lated-amplitude PWM current (variable duty cycle) that
can provide control over the LED brightness (see
Figures 1 and 2).
16
15
14
13
16
15
14
13
1
OUT
OUT
EN
N.C.
N.C.
GND 12
I LED
1
OUT
OUT
EN
N.C.
N.C.
GND 12
I LED
V IN
C1
2
3
IN
IN
MAX16800
V5 11
CS- 10
D1
C2
R SENSE
V IN
C1
2
3
IN
IN
MAX16800
V5 11
CS- 10
D1
C2
R SENSE
4
N.C.
CS+ 9
4
N.C.
CS+ 9
N.C.
5
N.C.
6
N.C.
7
N.C.
8
N.C.
5
N.C.
6
N.C.
7
N.C.
8
Figure 1. Pulse Application with V IN at a Constant Voltage
Figure 2. Pulse Application with EN Connected to V IN
6
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ATFC-0603-2N2-BT | INDUCTOR THIN FILM 2.2NH 0603 |
| LM7824ACT | IC REG LDO 24V 1A TO-220 |
| RSM02DREN | CONN EDGECARD 4POS .156 EYELET |
| LM7818ACT | IC REG LDO 18V 1A TO-220 |
| LM7808ACT | IC REG LDO 8V 1A TO-220 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16801AEUA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX16801AEUA+ | 功能描述:LED照明驱动器 Offline & DC/DC PWM for HB LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16801AEUA+T | 功能描述:LED照明驱动器 Offline & DC/DC PWM for HB LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16801BEUA | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX16801BEUA+ | 功能描述:LED照明驱动器 Offline & DC/DC PWM for HB LED Driver RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。