- 您现在的位置：买卖IC网 > Datasheet目录989 > MAX16807EVKIT+ (Maxim Integrated Products)EVAL KIT FOR MAX16807 Datasheet资料下载
参数资料
| 型号： | MAX16807EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | EVAL KIT FOR MAX16807 |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 50mA |
| 输出及类型： | 8，非隔离 |
| 输出电压： | 32V |
| 特点： | 可调光 |
| 输入电压： | 9 ~ 16 V |
| 已供物品： | 板 |
| 已用 IC / 零件： | MAX16807 |
Integrated 8-Channel LED Driver with
Switch-Mode Boost and SEPIC Controller
Pin Description
PIN
1, 13, 28
2
3
4
5
6–9
10
11
12
14
15, 16
17
18
19
20–23
24
25
26
27
—
NAME
N.C.
AGND
OUT
V CC
REF
OUT4–OUT7
OE
DOUT
SET
V+
PGND
DIN
CLK
LE
OUT0–OUT3
COMP
FB
CS
RTCT
EP
FUNCTION
No Connection. Not internally connected. Leave unconnected.
Analog Ground
MOSFET Driver Output OUT. Connects to the gate of the external n-channel MOSFET.
Power-Supply Input. Bypass V CC to AGND with a 0.1μF ceramic capacitor or a parallel combination
of a 0.1μF and a higher value ceramic capacitor.
5V Reference Output. Bypass REF to AGND with a 0.1μF ceramic capacitor.
LED Driver Outputs. OUT4–OUT7 are open-drain, constant-current-sinking outputs rated for 36V.
Active-Low Output Enable Input. Drive OE low to PGND to enable the OUT0–OUT7. Drive OE high to
disable OUT0–OUT7.
Serial-Data Output. Data is clocked out of the 8-bit internal shift register to DOUT on CLK’s rising
edge.
LED Current Setting. Connect R SET from SET to PGND to set the LED current.
LED Driver Positive Supply Voltage. Bypass V+ to PGND with a 0.1μF ceramic capacitor.
Power Ground
Serial-Data Input
Serial-Clock Input
Latch-Enable Input. Data is loaded transparently from the internal shift register(s) to the output
latch(es) while LE is high. Data is latched into the output latch(es) on LE’s falling edge, and retained
while LE is low.
LED Driver Outputs. OUT0–OUT3 are open-drain, constant-current-sinking outputs rated for 36V.
Error-Amplifier Output
Error-Amplifier Inverting Input
PWM Controller Current-Sense Input
PWM Controller Timing Resistor/Capacitor Connection. A resistor R T from RTCT to REF and a
capacitor C T from RTCT to AGND set the oscillator frequency.
Exposed Paddle. Connect to the ground plane for improved power dissipation. Do not use as the
only ground connection for the part.
Detailed Description
The MAX16807 LED driver includes an internal switch-
mode controller that can be used as boost or buck-
boost (SEPIC) converters to generate the voltage
necessary to drive the multiple strings of LEDs. This
device incorporates an integrated low-side driver, a
programmable oscillator (20kHz to 1MHz), an error
amplifier, a low-voltage (300mV) current sense for high-
er efficiency, and a 5V reference to power up external
circuitry (see Figures 1a, 1b, and 1c).
The MAX16807 LED driver includes a 4-wire serial
interface and a current-mode PWM controller to gener-
ate the necessary voltage for driving eight open-drain,
constant-current-sinking output ports. The driver uses
current-sensing feedback circuitry (not simple current
mirrors) to ensure very small current variations over the
full allowed range of output voltage (see the Typical
Operating Characteristics). The 4-wire serial interface
comprises an 8-bit shift register and an 8-bit transpar-
ent latch. The shift register is written through a clock
input, CLK, and a data input, DIN, and the data propa-
gates to a data output, DOUT. The data output allows
multiple drivers to be cascaded and operated together.
The contents of the 8-bit shift register are loaded into
the transparent latch through a latch-enable input, LE.
The latch is transparent to the shift register outputs
when high and latches the current state on the falling
edge of LE. Each driver output is an open-drain, con-
stant-current sink that should be connected to the cath-
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16809EVKIT+ | EVAL KIT FOR MAX16809 |
| MAX16814EVKIT+ | KIT EAL FOR MAX16814 |
| MAX16816EVKIT+ | KIT EVAL FOR MAX16816 LED DRIVER |
| MAX16818EVKIT+ | KIT EVALUATION FOR MAX16818 |
| MAX16820EVKIT+ | EVAL KIT FOR MAX16820 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16807EVKIT+ | 功能描述:LED 照明开发工具 MAX16807 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX16808AUI+ | 制造商:Maxim Integrated Products 功能描述:LED DRVR 3V TO 5.5V 28TSSOP EP - Rail/Tube |
| MAX16808AUI+T | 制造商:Maxim Integrated Products 功能描述:LED DRVR 3V TO 5.5V 28TSSOP EP - Tape and Reel |
| MAX16809ATU+ | 功能描述:LED照明驱动器 8Ch w/Switch-Mode Boost & SEPIC Ctlr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16809ATU+T | 功能描述:LED照明驱动器 8Ch w/Switch-Mode Boost & SEPIC Ctlr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。