- 您现在的位置：买卖IC网 > Datasheet目录989 > MAX16816EVKIT+ (Maxim Integrated Products)KIT EVAL FOR MAX16816 LED DRIVER Datasheet资料下载
参数资料
| 型号： | MAX16816EVKIT+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 24/33页 |
| 文件大小： | 0K |
| 描述： | KIT EVAL FOR MAX16816 LED DRIVER |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1 |
| 电流 - 输出 / 通道： | 1.33A |
| 输出及类型： | 1，非隔离 |
| 输出电压： | 28V |
| 特点： | 可调光，USB 接口 |
| 输入电压： | 9 ~ 40 V |
| 已供物品： | 板，缆线，CD |
| 已用 IC / 零件： | MAX16816 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Programmable Switch-Mode LED Driver
with Analog-Controlled PWM Dimming
Careful PCB layout is critical to achieve low switching
losses and clean, stable operation. Use a multilayer
board whenever possible for better noise performance
and power dissipation. Follow these guidelines for
good PCB layout:
? Use a large copper plane under the MAX16816
package. Ensure that all heat-dissipating compo-
nents have adequate cooling. Connect the
exposed pad of the device to the ground plane.
? Isolate the power components and high current
paths from sensitive analog circuitry.
? Keep the high-current paths short, especially at the
ground terminals. This practice is essential for sta-
ble, jitter-free operation. Keep switching loops short.
? Connect AGND, SGND, and QGND to a ground
plane. Ensure a low-impedance connection
between all ground points.
? Keep the power traces and load connections
short. This practice is essential for high efficiency.
Use thick copper PCBs (2oz vs. 1oz) to enhance
full-load efficiency.
? Ensure that the feedback connection to FB is short
and direct.
? Route high-speed switching nodes away from the
sensitive analog areas.
? To prevent discharge of the compensation capaci-
tors, C 1 and C 2 , during the off-time of the dimming
cycle, ensure that the PCB area close to these
components has extremely low leakage.
Discharge of these capacitors due to leakage may
result in degraded dimming performance.
1-Wire Interface
EEPROM implementation uses a 1-Wire communica-
tion method. A 1-Wire net-based system consists of
three main elements: a bus master with controlling
software, the wiring and associated connectors, and
1-Wire devices. Data on the 1-Wire net is transferred
with respect to time slots. For example, the master pulls
the bus low and holds it for 15μs or less to write a logic
‘1’, and holds the bus low for at least 60μs to write a
logic ‘0’. During EEPROM programming the MAX16816
is a 1-Wire slave device only. Data and clock signals
are supplied through FAULT .
MAX16816 1-Wire Function Commands
Table 10 shows the list of 1-Wire function commands
for the MAX16816. Use these commands to start the
programming mode, write to the on-chip EEPROM, and
read EEPROM through the 1-Wire interface.
PASS_CODE_ONE: The PASS_CODE_ONE sequence
is the first code that the MAX16816 must receive from
the master. PASS_CODE_ONE must be received within
the initial 8ms programming window after startup.
PASS_CODE_TWO: The PASS_CODE_TWO sequence
is the second code that the MAX16816 must receive
during the 8ms programming window. The MAX16816
will start searching for PASS_CODE_TWO only after
PASS_CODE_ONE has been received.
EXT_EEM_MODE: The EXT_EEM_MODE command
clears the PASS_CODE_ONE and PASS_CODE_TWO
verification register. Use this command to exit program-
ming mode.
SET_WRITE_EE: The SET_WRITE_EE command is the
write all command for the MAX16816. When the device
detects the SET_WRITE_EE command the write
Table 10. MAX16816 1-Wire Function Commands
COMMAND
D7
D6
D5
DATA BIT CODE
D4 D3
D2
D1
D0
HEX
CODE
PASS_CODE_ONE
PASS_CODE_TWO
EXT_EEM_MODE
SET_WRITE_EE
SET_WRITE_SCH
SET_READ_SCH
0
0
0
0
ADD
0
0
0
0
0
ADD
0
1
0
0
0
ADD
0
0
0
0
0
ADD
0
1
1
0
0
DATA
0
0
0
0
1
DATA
1
0
0
0
0
DATA
1
1
1
1
0
DATA
0
29h
09h
01h
04h
—
06h
24
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX16818EVKIT+ | KIT EVALUATION FOR MAX16818 |
| MAX16820EVKIT+ | EVAL KIT FOR MAX16820 |
| MAX16821BEVKIT+ | KIT EVAL FOR MAX16821B |
| MAX16822BEVKIT+ | KIT EVAL FOR MAX16822 |
| MAX16823EVKIT+ | EVAL KIT FOR MAX16823 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16816EVKIT+ | 功能描述:LED 照明开发工具 MAX16816 Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| MAX16818ATI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ATI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+ | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16818ETI+T | 功能描述:LED照明驱动器 1.5MHz 30A w/Rapid LED Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
发布紧急采购，3分钟左右您将得到回复。