- 您现在的位置：买卖IC网 > PDF目录20781 > MAX16821BATI+ (Maxim Integrated)IC LED DRIVR HIGH BRIGHT 28-TQFN PDF资料下载
参数资料
| 型号： | MAX16821BATI+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVR HIGH BRIGHT 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 拓扑： | 高端，低端，PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载，背光 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 125kHz ~ 1.5MHz |
| 电源电压： | 4.75 V ~ 5.5 V，7 V ~ 28 V |
| 输出电压： | 5.1V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
High-Power Synchronous HBLED
Drivers with Rapid Current Pulsing
Pin Description
PIN
1
2, 7
3
4
5
6
8, 22, 25
9
10
11
12
13
14
15
16
17
18
19
20
21
23
24
26
27
28
—
NAME
PGND
N.C.
DL
BST
LX
DH
SGND
CLKOUT
MODE
EN
RT/SYNC
OUTV
I.C.
OVI
CLP
EAOUT
EAN
DIFF
CSN
CSP
SENSE-
SENSE+
IN
V CC
V DD
EP
FUNCTION
Power-Supply Ground
No Connection. Not internally connected.
Low-Side Gate-Driver Output
Boost-Flying Capacitor Connection. Reservoir capacitor connection for the high-side MOSFET driver
supply. Connect a ceramic capacitor between BST and LX.
High-Side MOSFET Source Connection
High-Side Gate-Driver Output
Signal Ground. SGND is the ground connection for the internal control circuitry. Connect SGND and PGND
together at one point near the IC.
Oscillator Output. If MODE is low, the rising edge of CLKOUT phase shifts from the rising edge of DH by
180°. If MODE is high, the rising edge of CLKOUT phase shifts from the rising edge of DL by 180°.
Buck/Boost Mode Selection Input. Drive MODE low for low-side buck mode operation. Drive MODE high for
boost or high-side buck mode operation. MODE has an internal 5μA pulldown current to ground.
Output Enable. Drives EN high or leave unconnected for normal operation. Drive EN low to shut down the
power drivers. EN has an internal 15μA pullup current.
Switching Frequency Programming. Connect a resistor from RT/SYNC to SGND to set the internal oscillator
frequency. Drive RT/SYNC to synchronize the switching frequency with an external clock.
Inductor Current-Sense Output. OUTV is an amplifier output voltage proportional to the inductor current.
The voltage at OUTV = 135 x (V CSP - V CSN ).
Internally Connected. Connect to SGND for proper operation.
Overvoltage Protection. When OVI exceeds the programmed output voltage by 12.7%, the low-side and
the high-side drivers are turned off. When OVI falls 20% below the programmed output voltage, the drivers
are turned on after power-on reset and soft-start cycles are completed.
Current-Error-Amplifier Output. Compensate the current loop by connecting an RC network to ground.
Voltage-Error-Amplifier Output. Connect EAOUT to the external gain-setting network.
Voltage-Error-Amplifier Inverting Input
Differential Remote-Sense Amplifier Output. DIFF is the output of a precision amplifier with SENSE+ and
SENSE- as inputs.
Current-Sense Differential Amplifier Negative Input. The differential voltage between CSN and CSP is
amplified internally by the current-sense amplifier (Gain = 34.5) to measure the inductor current.
Current-Sense Differential Amplifier Positive Input. The differential voltage between CSP and CSN is
amplified internally by the current-sense amplifier (Gain = 34.5) to measure the inductor current.
Differential LED Current-Sensing Negative Input. Connect SENSE- to the negative side of the LED current-
sense resistor or to the negative feedback point.
Differential LED Current-Sensing Positive Input. Connect SENSE+ to the positive side of the LED current-
sense resistor, or to the positive feedback point.
Supply Voltage Input. Connect IN to V CC , for a 4.75V to 5.5V input supply range.
Internal +5V Regulator Output. V CC is derived from V IN . Bypass V CC to SGND with 4.7μF and 0.1μF
ceramic capacitors.
Low-Side Driver Supply Voltage
Exposed Pad. EP is internally connected to SGND. Connect EP to a large-area ground plane for effective
power dissipation. Connect EP to SGND. Do not use as a ground connection.
_______________________________________________________________________________________
7
相关PDF资料 |
PDF描述 |
|---|---|
| LQP03TN3N9C00D | INDUCTOR 3.9NH 170MA 0201 |
| MAX7302AEE+ | IC LED DRIVER LINEAR 16-QSOP |
| GBC10DCAD | CONN EDGECARD 20POS R/A .100 SLD |
| EBC28DCSN-S288 | CONN EDGECARD 56POS .100 EXTEND |
| MAX6964ATG+ | IC LED DRIVER LINEAR 24-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX16821BATI+ | 功能描述:LED照明驱动器 Synchronous HB w/Rapid Current Puls RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16821BATI+T | 功能描述:LED照明驱动器 Synchronous HB w/Rapid Current Puls RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16821BATI+TW | 功能描述:LED照明驱动器 High-Power Synchronous HBLED Drivers with Rapid Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16821BATI+W | 功能描述:LED照明驱动器 High-Power Synchronous HB LED Drivers with Rapid Current Pulsing RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| MAX16821BEVKIT+ | 功能描述:LED 照明开发工具 MAX16821B Eval Kit RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。