- 您现在的位置：买卖IC网 > PDF目录383332 > MAX1700-MAX1701 (Maxim Integrated Products, Inc.) 1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters PDF资料下载
参数资料
| 型号： | MAX1700-MAX1701 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | DC/DC变换器 |
| 英文描述： | 1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters |
| 中文描述： | 1节至3节电池，大功率1A中，低噪声，升压型DC - DC转换器 |
| 文件页数： | 15/16页 |
| 文件大小： | 248K |
| 代理商： | MAX1700-MAX1701 |
low-noise power for DSP, control, and RF circuitry.
Typically, RF phones spend most of their life in standby
mode with only short periods in transmit/receive mode.
During standby, maximize battery life by setting
CLK/SEL = 0; this places the IC in low-power mode (for
the lowest quiescent power consumption).
Designing a PC Board
High switching frequencies and large peak currents
make PC board layout an important part of design.
Poor design can cause excessive EMI and ground-
bounce, both of which can cause instability or regula-
tion errors by corrupting the voltage and current
feedback signals.
Power components (such as the inductor, converter IC,
filter capacitors, and output diode) should be placed as
close together as possible, and their traces should be
kept short, direct, and wide. A separate low-noise
ground plane containing the reference and signal
grounds should only connect to the power-ground
plane at one point. This minimizes the effect of power-
ground currents on the part. Consult the MAX1701 EV
kit manual for a layout example.
On multilayer boards, do not connect the ground pins
of the power components using vias through an internal
ground plane. Instead, place them close together and
route them in a star-ground configuration using compo-
nent-side copper. Then use vias to connect the star
ground to the internal ground plane.
Keep the voltage feedback network very close to the
IC, within 0.2in. (5mm) of the FB pins. Keep noisy
traces, such as from the LX pin, away from the voltage
feedback networks. Separate them with grounded
copper. Consult the MAX1700 evaluation kit for a full
PC board example.
S oft-S tart
To implement soft-start, set CLK/SEL low on power-up;
this forces low-power operation and reduces the peak
switching current to 550mA max. Once the circuit is in
regulation and start-up transients have settled,
CLK/SEL can be set high for full-power operation.
Intermittent S upply/Battery Connec tions
When boosting an input supply connected with a
mechanical switch, or a battery connected with spring
contacts, input power may sometimes be intermittent
as a result of contact bounce. When operating in PFM
mode with input voltages greater than 2.5V, restarting
after such dropouts may initiate high current pulses that
interfere with the MAX1700/MAX1701 internal MOSFET
switch control. If contact or switch bounce is anticipat-
ed in the design, use one of the following solutions.
1) Connect a capacitor (C
ONB
) from
ONB
to V
IN
, a 1M
resistor (R
ONB
) from
ONB
to GND, and tie ONA to GND
(Figure 12). This RC network differentiates fast input
edges at V
IN
and momentarily holds the IC off until V
IN
settles. The appropriate value of C
ONB
is 10
-5
times the
total output filter capacitance (C
OUT
), so a C
OUT
of
200μF results in C
ONB
= 2nF.
2) Use the system microcontroller to hold the
MAX1700/MAX1701 in shut down from the time when
power is applied (or reapplied) until the output capaci-
tance (C
OUT
) has charged to at least the input voltage.
Power-on reset times of tens of milliseconds accom-
plish this.
3) Ensure that the IC operates, or at least powers up, in
PWM mode (CLK/SEL = high). Activate PFM mode only
after the V
OUT
has settled and all of the system’s power-
on reset flags are cleared.
M
1-Cell to 3-Cell, High-Power (1A),
Low-Noise, S tep-Up DC-DC Converters
______________________________________________________________________________________
15
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
LBP
LBO
POUT
OUT
LX
PGND
FB
AIN
AO
MAX1701
QSOP
LBN
REF
POK
CLK/SEL
GND
ONB
ONA
TOP VIEW
Pin Configurations (c ontinued)
Figure 12. Connecting C
ONB
and R
ONB
when Switch or
Battery-Contact Bounce Is Anticipated
POUT
OUT
LX
13
14
15
8
7
C
OUT
200
μ
F
C
2nF
R
ONB
ONA
ONB
MAX1700
MAX1701
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1700EEE | 1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters |
| MAX1701EEE | 18-Bit Universal Bus Transceivers With 3-State Outputs 56-SSOP -40 to 85 |
| MAX1702B | Triple-Output Power-Management IC for Microprocessor-Based Systems |
| MAX1702BEGX | Triple-Output Power-Management IC for Microprocessor-Based Systems |
| MAX1703 | 1-Cell to 3-Cell, High-Power 1.5A, Low-Noise, Step-Up DC-DC Converter |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17010AETL+ | 功能描述:LCD 驱动器 Internal-Switch Boost Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX17010AETL+T | 功能描述:LCD 驱动器 Internal-Switch Boost Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX17010ETL+ | 功能描述:LCD 驱动器 Internal-Switch Boost Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX17010ETL+T | 功能描述:LCD 驱动器 Internal-Switch Boost Regulator RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX17010EVKIT+ | 功能描述:电源管理IC开发工具 MAX17010 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。