- 您现在的位置：买卖IC网 > PDF目录1838 > MAX17003AETJ+T (Maxim Integrated Products)IC SUPPLY CTLR NOTEBOOKS 32TQFN PDF资料下载
参数资料
| 型号： | MAX17003AETJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 25/36页 |
| 文件大小： | 0K |
| 描述： | IC SUPPLY CTLR NOTEBOOKS 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | 控制器，笔记本电脑电源系统 |
| 输入电压： | 6 V ~ 26 V |
| 输出数： | 4 |
| 输出电压： | 3.3V，5V，2 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
High-Efficiency, Quad-Output, Main Power-
Supply Controllers for Notebook Computers
Ferrite cores are often the best choice, although pow-
dered iron is inexpensive and can work well at 200kHz.
The core must be large enough not to saturate at the
peak inductor current (I PEAK ):
this case, subtract V OUT5 from the secondary voltage
(V SEC - V OUT5 ) in the transformer turns-ratio equation
above. The secondary diode in coupled-inductor appli-
cations must withstand flyback voltages greater than
I PEAK = I LOAD ( MAX ) +
Δ I INDUCTOR
2
60V. Common silicon rectifiers, such as the 1N4001, are
also prohibited because they are too slow. Fast silicon
rectifiers, such as the MURS120, are the only choice.
The flyback voltage across the rectifier is related to the
Transformer Design (for
MAX17003A/MAX17004A Auxiliary Output)
A coupled inductor or transformer can be substituted
for the inductor in the 5V SMPS to create an auxiliary
output (Figure 1). The MAX17003A/MAX17004A are
particularly well suited for such applications because
the secondary feedback threshold automatically trig-
gers DL5 even if the 5V output is lightly loaded.
The power requirements of the auxiliary supply must be
considered in the design of the main output. The trans-
former must be designed to deliver the required current
in both the primary and the secondary outputs with the
proper turns ratio and inductance. The power ratings of
the synchronous-rectifier MOSFETs and the current limit
in the MAX17003A/MAX17004A must also be adjusted
accordingly. Extremes of low input-output differentials,
widely different output loading levels, and high turns
ratios can further complicate the design due to parasitic
transformer parameters such as interwinding capaci-
tance, secondary resistance, and leakage inductance.
Power from the main and secondary outputs is com-
bined to get an equivalent current referred to the main
V IN - V OUT5 difference, according to the transformer
turns ratio:
V FLYBACK = V SEC + (V IN – V OUT5 ) x N
where N is the transformer turns ratio (secondary wind-
ings/primary windings), and V SEC is the maximum sec-
ondary DC output voltage. If the secondary winding is
returned to V OUT5 instead of ground, subtract V OUT5
from V FLYBACK in the equation above. The diode ’s
reverse breakdown voltage rating must also accommo-
date any ringing due to leakage inductance. The
diode’s current rating should be at least twice the DC
load current on the secondary output.
Transient Response
The inductor ripple current also impacts transient-
response performance, especially at low V IN - V OUT dif-
ferentials. Low inductor values allow the inductor
current to slew faster, replenishing charge removed
from the output filter capacitors by a sudden load step.
The total output-voltage sag is the sum of the voltage
sag while the inductor is ramping up, and the voltage
sag before the next pulse can occur:
(
output. Use this total current to determine the current
limit (see the Setting the Current Limit section):
I TOTAL = P TOTAL /V OUT5
where I TOTAL is the equivalent output current referred
to the main output, and P TOTAL is the sum of the output
V SAG =
L ( Δ I LOAD ( MAX ) ) 2
2 C OUT V IN xD MAX ? V OUT
Δ I LOAD ( MAX ) ( t ? Δ t )
)
+
power from both the main output and the secondary
output:
C OUT
N =
V SEC + V FWD
V OUT 5 + V RECT + V SENSE
where D MAX is the maximum duty factor (see the
Electrical Characteristics table), t is the switching
period (1/f OSC ), and Δ t equals V OUT /V IN x t when in
PWM mode, or L x 0.2 x I MAX /(V IN - V OUT ) when in skip
≈ ( Δ I LOAD ( MAX ) ) 2 L
where N is the transformer turns ratio, V SEC is the mini-
mum required rectified secondary voltage, V FWD is the
forward drop across the secondary rectifier, V OUT5(MIN)
is the minimum value of the main output voltage, and
V RECT is the on-state voltage drop across the synchro-
nous-rectifier MOSFET. The transformer secondary
return is often connected to the main output voltage
instead of ground to reduce the necessary turns ratio. In
mode. The amount of overshoot during a full-load to no-
load transient due to stored inductor energy can be
calculated as:
V SOAR
2 C OUT V OUT
______________________________________________________________________________________
25
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17003ETJ+T | IC PS CTRLR FOR NOTEBOOKS 32TQFN |
| MAX17005AETP+ | IC BATT CHARGER 1.2MHZ 20TQFN |
| MAX17005BETP+ | IC BATT CHARGER 1.2MHZ 20-TQFN |
| MAX17007GTI+T | IC CTRLR QPWM GRAPHICS 28TQFN |
| MAX1700EEE+T | IC REG BST SYNC ADJ 0.8A 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17003ETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17003ETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17004AETJ+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX17004ETJ+ | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX17004ETJ+T | 功能描述:电压模式 PWM 控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。