- 您现在的位置：买卖IC网 > PDF目录16578 > MAX1702BETX+ (Maxim Integrated Products)IC PWR MNG TRPL OUT 36-TQFN PDF资料下载
参数资料
| 型号： | MAX1702BETX+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/19页 |
| 文件大小： | 0K |
| 描述： | IC PWR MNG TRPL OUT 36-TQFN |
| 标准包装： | 50 |
| 应用： | 处理器 |
| 电源电压： | 2.6 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 36-WFQFN 裸露焊盘 |
| 供应商设备封装： | 36-TQFN 裸露焊盘（6x6） |
| 包装： | 管件 |
Triple-Output Power-Management IC for
Microprocessor-Based Systems
Functional Diagram
IN
output, providing up to 400mA output current. The third
output, REG3, is designed to power memory. REG3 out-
put voltage is set to one of 3 voltages; 3.3V (PGM3 =
IN), 2.5V (PGM3 = REF), or 1.8V (PGM3 = GND) and
delivers up to 800mA of output current. All three regula-
MAX1702B
REG1
INP1
tors utilize a proprietary regulation scheme allowing
PWM operation at medium to heavy loads, and automat-
DBI
LBI
LBO
OUTOK
ON2
DEAD-
BATTERY
DETECTOR
LOW-
BATTERY
DETECTOR
ON/OFF
CONTROL
LOGIC
DBO
EN
REF
DC-DC BUCK
WITH SKIP
1MHz PWM
REG2
POK
EN
LX1
PG1
OUT1
COMP1
INP2
LX2
ically switch to pulse skipping at light loads for
improved efficiency. Under low-battery conditions, the
MAX1702B issues a warning ( LBO output).
The MAX1702B employs PWM control at medium and
heavy loads, and skip mode at light loads (below
approximately 80mA) to improve efficiency and reduce
quiescent current to 485μA. During skip operation, the
MAX1702B switches only as needed to service the load,
reducing the switching frequency and associated losses
in the internal switch, the synchronous rectifier, and the
external inductor.
There are three steady-state operating conditions for the
MAX1702B. The device performs in continuous conduc-
tion for heavy loads. The inductor current becomes dis-
continuous at light loads, requiring the synchronous
REF
rectifier to be turned off before the end of a cycle as the
DC-DC BUCK
WITH SKIP
1MHz PWM
REG3
PG2
FB2
COMP2
INP3
inductor current reaches zero. The device enters into
skip mode when the converter output voltage exceeds
its regulation limit before the inductor current reaches
the pulse-skip threshold.
During skip mode, a switching cycle initiates when the
RSO
MR
RESET
TIMER
EN
LX3
output voltage drops below the regulation voltage. The
P-channel MOSFET switch turns on and conducts cur-
rent to the output-filter capacitor and load until the
inductor current reaches the pulse-skip current thresh-
old. Then the main switch turns off, and the current flows
BANDGAP
REFERENCE
GND
REF
REF
DC-DC BUCK
WITH SKIP
1MHz PWM
PG3
OUT3
COMP3
PGM3
through the synchronous rectifier to the output-filter
capacitor and the load. The synchronous rectifier is
turned off when the inductor current approaches zero.
The MAX1702B waits until the output voltage drops below
the regulation voltage again to initiate the next cycle.
100% Duty-Cycle Operation
If the inductor current does not rise sufficiently to sup-
ply the load during the on-time, the switch remains on,
Detailed Description
The MAX1702B triple-output step-down DC-DC convert-
er is ideal for powering PDA, palmtop, and subnotebook
computers. Normally, these devices require separate
power supplies for the processor core, memory, and the
peripheral circuitry. The MAX1702B ’ s REG1 provides a
fixed 3.3V output designed to power the microprocessor
I/O and other peripheral circuitry. REG1 delivers up to
900mA output current. The microprocessor core is pow-
ered from REG2, which has an adjustable 0.7V to V IN
allowing operation up to 100% duty cycle. This allows
the output voltage to maintain regulation while the input
voltage approaches the regulation voltage. Dropout
voltage is the output current multiplied by the on-resis-
tance of the internal switch and inductor, approximately
220mV for an 800mA load for REG1 and REG3 and
150mV for a 400mA load on REG2.
Near dropout, the on-time may exceed one PWM clock
cycle; therefore, small amplitude subharmonic ripple
can occur in the output voltage. During dropout, the
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| V300C28T75BF3 | CONVERTER MOD DC/DC 28V 75W |
| VI-J1B-EZ-S | CONVERTER MOD DC/DC 95V 25W |
| HCM11DRYS | CONN EDGECARD 22POS DIP .156 SLD |
| V300C28E150BL3 | CONVERTER MOD DC/DC 28V 150W |
| 7-846290-8 | LGH-4 SGL MOLDED END LEAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1702BETX+ | 功能描述:PMIC 解决方案 Triple-Output for MPU-Based System RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1702BETX+T | 功能描述:PMIC 解决方案 Triple-Output for MPU-Based System RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1702BETX-T | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX1702EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17030EVKIT+ | 功能描述:电源管理IC开发工具 MAX17030 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。