- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17044G+T (Maxim Integrated Products)IC FUEL GAUGE LI-ION 8-TDFN PDF资料下载
参数资料
| 型号： | MAX17044G+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 7/14页 |
| 文件大小： | 0K |
| 描述： | IC FUEL GAUGE LI-ION 8-TDFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 10,000 |
| 系列： | ModelGauge™ |
| 功能： | 燃料，电量检测计/监控器 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 2.5 V ~ 4.5 V |
| 工作温度： | -20°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-WFDFN 裸露焊盘 |
| 供应商设备封装： | 8-TDFN-EP（2x3） |
| 包装： | 带卷 (TR) |
| 其它名称： | 90-2772G+BTR |
MAX17043/MAX17044
Compact, Low-Cost 1S/2S Fuel Gauges
with Low-Battery Alert
IC Power-Up
When the battery is first inserted into the system, there
is no previous knowledge about the battery’s SOC. The
IC assumes that the battery has been in a relaxed state
for the previous 30min. The first A/D voltage measure-
ment is translated into a best “first guess” for the SOC.
Initial error caused by the battery not being in a relaxed
state fades over time, regardless of cell loading follow-
ing this initial conversion. Because the SOC determina-
tion is convergent rather than divergent (as in a
coulomb counter), this initial error does not have a long-
lasting impact.
Quick-Start
A quick-start allows the MAX17043/MAX17044 to restart
fuel-gauge calculations in the same manner as initial
power-up of the IC. For example, if an application’s
power-up sequence is exceedingly noisy such that
excess error is introduced into the IC’s “first guess” of
SOC, the host can issue a quick-start to reduce the
error. A quick-start is initiated by a rising edge on the
QSTRT pin, or through software by writing 4000h to the
MODE register.
ALERT Interrupt
The MAX17043/MAX17044 have an interrupt feature
that alerts a host microprocessor whenever the cell's
state of charge, as defined by the SOC register, falls
below a predefined alert threshold set at address 0Dh
of the CONFIG register.
When an alert is triggered, the IC drives the ALRT pin to
logic-low and sets the ALRT bit in the CONFIG register
to logic 1. The ALRT pin remains logic-low until the host
software writes the ALRT bit to logic 0 to clear the inter-
rupt. Clearing the ALRT bit while SOC is below the alert
threshold does not generate another interrupt. The SOC
register must first rise above and then fall below the alert
threshold value before another interrupt is generated.
Table 1. Register Summary
Note that the alert function is not disabled at IC power-
up. If the first SOC calculation is below the threshold
setting, an interrupt is generated. Entering Sleep mode
does not clear the interrupt.
Sleep Mode
Holding both SDA and SCL logic-low forces the
MAX17043/MAX17044 into Sleep mode. While in Sleep
mode, all IC operations are halted and power drain of
the IC is greatly reduced. After exiting Sleep mode,
fuel-gauge operation continues from the point it was
halted. SDA and SCL must be held low for at least 2.5s
to guarantee transition into Sleep mode. Afterwards, a
rising edge on either SDA or SCL immediately transi-
tions the IC out of Sleep mode.
Alternatively, Sleep mode can be entered by setting the
SLEEP bit in the CONFIG register to logic 1 through I 2 C
communication. If the SLEEP bit is set to logic 1, the
only way to exit Sleep mode is to write SLEEP to logic 0
or power-on reset the IC.
Power-On Reset (POR)
Writing a value of 0054h to the COMMAND register caus-
es the MAX17043/MAX17044 to completely reset as if
power had been removed. The reset occurs when the last
bit has been clocked in. The IC does not respond with an
I 2 C ACK after this command sequence.
Registers
All host interaction with the MAX17043/MAX17044 is
handled by writing to and reading from register loca-
tions. The MAX17043/MAX17044 have six 16-bit regis-
ters: SOC , VCELL , MODE , VERSION , CONFIG , and
COMMAND . Register reads and writes are only valid if
all 16 bits are transferred. Any write command that is
terminated early is ignored. The function of each regis-
ter is described as follows. All remaining address loca-
tions not listed in Table 1 are reserved. Data read from
reserved locations is undefined.
ADDRESS
(HEX)
02h –03h
04h –05h
06h –07h
08h –09h
0Ch –0Dh
FEh –FFh
REGISTER
VCELL
SOC
MODE
VERSION
CONFIG
COMMAND
DESCRIPTION
Reports 12-bit A/D measurement of battery voltage.
Reports 16-bit SOC result calculated by ModelGauge algorithm.
Sends special commands to the IC.
Returns IC version.
Battery compensation. Adjusts IC performance based on
application conditions.
Sends special commands to the IC.
READ/
WRITE
R
R
W
R
R/W
W
DEFAULT
(HEX)
—
—
—
—
971Ch
—
Maxim Integrated
7
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17049G+ | IC FUEL/GAS GAUGE LI-ION 8TDFN |
| MAX17062ETB+T | IC TFT-LCD DC/DC CONV 10-TDFN |
| MAX17067EUA+T | IC REG BOOST ADJ 0.3A 8UMAX |
| MAX1706EEE+T | IC REG BOOST ADJ 0.4A 16QSOP |
| MAX17075ETG+T | IC DC-DC CONV W/CHRG PUMP 24TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17044X+ | 功能描述:电池管理 1S/2S Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17044X+T10 | 功能描述:电池管理 1S/2S Fuel Gauge RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17044X+U | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX17047EVKIT# | 制造商:Maxim Integrated Products 功能描述:EVAL KIT MAX17047(M3 ALGORITHM) - Boxed Product (Development Kits) |
| MAX17047G+ | 制造商:Maxim Integrated Products 功能描述:MODELGAUGE M3 FUEL GAUGE - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。