- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17075ETG+T (Maxim Integrated Products)IC DC-DC CONV W/CHRG PUMP 24TQFN PDF资料下载
参数资料
| 型号： | MAX17075ETG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 14/23页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CONV W/CHRG PUMP 24TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 应用： | LCD 电视机/监控器 |
| 电流 - 电源： | 4mA |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-TQFN-EP（4x4） |
| 包装： | 带卷 (TR) |
MAX17075
Boost Regulator with Integrated Charge Pumps,
Switch Control, and High-Current Op Amp
On the rising edge of the internal clock, the controller
sets a flip-flop, turning on the n-channel MOSFET and
applying the input voltage across the inductor. The cur-
rent through the inductor ramps up linearly, storing
energy in its magnetic field. Once the sum of the cur-
rent-feedback signal and the slope compensation
exceed the COMP voltage, the controller resets the
flip-flop and turns off the MOSFET. Since the inductor
current is continuous, a transverse potential develops
across the inductor that turns on the diode (D1). The
voltage across the inductor then becomes the differ-
ence between the output voltage and the input voltage.
This discharge condition forces the current through the
inductor to ramp back down, transferring the energy
stored in the magnetic field to the output capacitor and
the load. The MOSFET remains off for the rest of the
clock cycle.
Positive Charge-Pump Regulator
The positive charge-pump regulator is typically used to
generate the positive supply rail for the TFT LCD gate-
driver ICs. The output voltage is set with an external
resistive voltage-divider from its output to GND with the
midpoint connected to FBP. The number of charge-
pump stages and the setting of the feedback divider
determine the output voltage of the positive charge-
pump regulator. The charge pump includes a high-side
p-channel MOSFET (P1) and a low-side n-channel
The error amplifier compares the feedback signal (FBP)
with a 1.25V internal reference. If the feedback signal is
below the reference, the charge-pump regulator turns
on P1 and turns off N1 when the rising edge of the
oscillator clock arrives, level shifting C15 and C17 by
V SUP volts. If the voltage across C POUT plus a diode
drop (V POUT + V DIODE ) is smaller than the level-shifted
flying capacitor voltage (V C17 + V SUP ), charge flows
from C17 to C POUT until diode D3-1 turns off. Similarly,
if the voltage across C16 plus a diode drop (V C16 +
V DIODE ) is smaller than the level-shifted flying capacitor
voltage (V C15 + V SUP ), charge flows from C15 to C16
until diode D2-1 turns off. The falling edge of the oscil-
lator clock turns off P1 and turns on N1, allowing V SUP
to charge up the flying capacitor C15 through D2-2 and
C16 to charge C17 through diode D3-2. If the feedback
signal is above the reference when the rising edge of
the oscillator comes, the regulator ignores this clock
edge and keeps N1 on and P1 off.
The MAX17075 also monitors the FBP voltage for
undervoltage conditions. If the V FBP is continuously
below 80% of the nominal regulation voltage for
approximately 50ms, the MAX17075 sets a fault latch,
shutting down all outputs except REF. Once the fault
condition is removed, cycle the input voltage (below the
UVLO falling threshold) to clear the fault latch and reac-
tivate the device.
MOSFET (N1) to control the power transfer as shown in
Figure 4.
INPUT
SUPPLY
SUP
MAX17075
C6
OSC
P1
C15
D2-2
REF
ERROR
AMPLIFIER
DRVP
D2-1
1.25V
N1
C17
D3-2
D3-1
C16
POUT
C14
POSITIVE CHARGE-PUMP REGULATOR
Figure 4. Positive Charge-Pump Regulator Block Diagram
14
FBP
Maxim Integrated
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17080GTL+T | IC CONTROLLER AMD SVI 40-TQFN |
| MAX17083ETG+T | IC REG BUCK ADJ 5A 24TQFN |
| MAX17085GTL+ | IC CHARGER/CTLR/LDO REG 40-TQFN |
| MAX1708EEE+T | IC REG BST 3.3V/5V/ADJ 5A 16QSOP |
| MAX17094ETM+T | IC REG BOOST ADJ 1A 7OUT 48TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17075EVKIT+ | 功能描述:电源管理IC开发工具 MAX17075 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17077AETM+ | 功能描述:低压差稳压器 - LDO Hybrid 500mA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX17077AETM+T | 功能描述:低压差稳压器 - LDO Hybrid 500mA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX17077AETM+W | 制造商:Maxim Integrated Products 功能描述:INTERNAL-SWITCH BOOST REGULATOR - Rail/Tube |
| MAX17077ETM+ | 功能描述:低压差稳压器 - LDO Hybrid 500mA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。