- 您现在的位置：买卖IC网 > PDF目录383332 > MAX1708 (Maxim Integrated Products, Inc.) High-Frequency, High-Power, Low-Noise, Step-Up DC-DC Converter PDF资料下载
参数资料
| 型号： | MAX1708 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | DC/DC变换器 |
| 英文描述： | High-Frequency, High-Power, Low-Noise, Step-Up DC-DC Converter |
| 中文描述： | 高频、大功率、低噪声、升压型DC-DC转换器 |
| 文件页数： | 12/13页 |
| 文件大小： | 332K |
| 代理商： | MAX1708 |
M
High-Frequency, High-Power, Low-Noise,
Step-Up DC-DC Converter
12
______________________________________________________________________________________
Diode Selection (D1)
The MAX1708
’
s high switching frequency demands a
high-speed rectifier. Use Schottky diodes (Table 3).
The diode
’
s current rating must exceed the maximum
load current, and its breakdown voltage must exceed
V
OUT
. The diode must be placed within 10mm of the
LX switching node and the output filter capacitor. The
diode also must be able to dissipate the power calcu-
lated by the following equation:
P
DIODE
= I
OUT
V
D
where I
OUT
is the average load current and V
D
is the
diode forward voltage at the peak switch current.
Capacitor Selection
Input Bypass Capacitor (C1)
A 150μF, low-ESR input capacitor will reduce peak cur-
rents and reflected noise due to inductor current ripple.
Lower ESR allows for lower input ripple current, but
combined ESR values up to 100m
are acceptable.
Smaller ceramic capacitors may also be used for light
loads or in applications that can tolerate higher input
current ripple.
Output Filter Capacitor (C2)
The output filter capacitor ESR must be kept under
30m
for stable operation. Polymer capacitors of
150μF (Panasonic EEFUE0J151R) typically exhibit
10m
of ESR. This translates to approximately 35mV of
output ripple at 3.5A switch current. Bypass the
MAX1708 IC supply input (OUT) with a 0.1μF ceramic
capacitor to GND and a 2
series resistor (R2, as
shown in Figure 1).
MAX1708 IC Power Dissipation
The major components of MAX1708 dissipated power
are switch conductance loss (P
SW
), capacitive loss
(P
CAP
), and switch transition loss (P
TRAN
). Numerical
examples provided in brackets ({ }) correspond to the
following condition:
{V
IN
= 3.3V, V
OUT
= 5V, V
D
= 0.5V, I
OUT
= 2A}
An important parameter to compute the power dissipat-
ed in the MAX1708 is the approximate peak switch cur-
rent (I
SW
):
P
D
= P
SW
+ P
CAP
+ P
TRAN
{0.472W}
P
SW
= (1 - D') I
SW
2
R
SW
{0.353W}
P
CAP
= (C
DIO
+ C
DSW
+ C
GSW
) (V
OUT
+ V
D
)
2
f {0.045W}
P
TRAN
= (V
OUT
+ V
D
) I
SW
t
SW
f / 3 {0.073W}
where:
R
SW
= switch resistance {80m
}
C
DIO
= catch-diode capacitance {500pF}
C
DSW
= switch drain capacitance {1250pF}
C
GSW
= switch gate capacitance {750pF}
f = switching frequency {600kHz}
t
SW
= switch turn-on or turn-off time {20ns}
Applications Information
Using a Momentary On/Off Switch
A momentary pushbutton switch can be used to turn
the MAX1708 on and off. As shown in Figure 5, when
ONA is pulled low and
ONB
is pulled high, the device
is off. When the momentary switch is pressed,
ONB
is
pulled low and the regulator turns on. The switch
should be on long enough for the microcontroller to exit
reset. The controller issues a logic high to ONA, which
guarantees that the device will stay on regardless of
the subsequent switch state. To turn the regulator off,
depress the switch long enough for the controller to
read the switch status and pull ONA low. When the
switch is released,
ONB
pulls high and the regulator
turns off.
Layout Considerations
Due to high inductor current levels and fast switching
waveforms, proper PC board layout is essential. Protect
I
I
D
A
D
V
V
V
SW
OUT
IN
+
OUT
D
'
{3 33
}
'
{ . }
0 6
=
=
μ
C
270k
ONB
ONA
0.1
μ
F
270k
ON/OFF
MAX1708
V
DD
I/O
I/O
Figure 5. Momentary Pushbutton On-Off Switch
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1708EEE | CHOKE COIL 2.2UH 1000MA SMD |
| MAX1709 | 4A, Low-Noise, High-Frequency, Step-Up DC-DC Converter |
| MAX1709EVKIT | MAX1709 Evaluation Kit |
| MAX1709ESE | 4A, Low-Noise, High-Frequency, Step-Up DC-DC Converter |
| MAX170CCPA | Serial Output 5.6us 12-Bit A/D Converter |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17080EVKIT+ | 功能描述:电源管理IC开发工具 MAX17080 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17080GTL+ | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17080GTL+T | 功能描述:开关变换器、稳压器与控制器 Integrated Circuits (ICs) Voltage Regulators - Special Purpose - IC CONTROLLER AMD SVI 40-TQFN RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MAX17081EVKIT+ | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17081EWV+ | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。