- 您现在的位置：买卖IC网 > PDF目录1839 > MAX17117ETJ+ (Maxim Integrated Products)IC REG INTERNAL SW BOOST 32TQFN PDF资料下载
参数资料
| 型号： | MAX17117ETJ+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/22页 |
| 文件大小： | 0K |
| 描述： | IC REG INTERNAL SW BOOST 32TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 60 |
| 应用： | LCD 监视器，笔记本电脑显示器 |
| 电流 - 电源： | 2.5mA |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-WFQFN 裸露焊盘 |
| 供应商设备封装： | 32-TQFN-EP（5x5） |
| 包装： | 托盘 |
Internal-Switch Boost Regulator with Integrated
7-Channel Scan Driver, Op Amp, and LDO
? ? η TYP ?
2 ?
? V IN ? V MAIN ? V IN
? I MAIN(EFF) OSC ? ? ? LIR ? ?
L = ? ? ? ?
?
?
Design Procedure
Main Step-Up Regulator
Inductor Selection
The minimum inductance value, peak current rating, and
series resistance are factors to consider when select-
ing the inductor. These factors influence the converter’s
efficiency, maximum output-load capability, transient-
response time, and output-voltage ripple. Physical size
and cost are also important factors to be considered.
The maximum output current, input voltage, output volt-
age, and switching frequency determine the inductor
value. Very high-inductance values minimize the current
ripple and therefore reduce the peak current, which
decreases core losses in the inductor and I 2 R losses in
the entire power path. However, large inductor values
also require more energy storage and more turns of wire,
which increase physical size and can increase I 2 R loss-
es in the inductor. Low-inductance values decrease the
physical size but increase the current ripple and peak
current. Finding the best inductor involves choosing the
best compromise among circuit efficiency, inductor size,
and cost.
The equations used here include a constant called LIR,
which is the ratio of the inductor peak-to-peak ripple cur-
rent to the average DC inductor current at the full-load
current. The best trade-off between inductor size and
of the maximum load current of the step-up regulator’s
output plus the contributions from the positive and nega-
tive charge pumps:
I MAIN(EFF) = I MAIN(MAX) + n VN × I VN + (n VP + 1) × I VP
where I MAIN(MAX) is the maximum step-up output cur-
rent, n VN is the number of negative charge-pump stag-
es, n VP is the number of positive charge-pump stages,
I VN is the negative charge-pump output current, and I VP
is the positive charge-pump output current, assuming
the initial pump source for I VP is V MAIN .
Calculate the approximate inductor value using the
typical input voltage (V IN ), the maximum output cur-
rent (I MAIN(EFF) ), the expected efficiency ( E TYP ) taken
from an appropriate curve in the Typical Operating
Characteristics , the desired switching frequency (f OSC ),
and an estimate of LIR based on the above discussion:
? V MAIN ? × f
Choose an available inductor value from an appropriate
inductor family. Calculate the maximum DC input current
at the minimum input voltage V IN(MIN) using conserva-
tion of energy and the expected efficiency at that operat-
ing point ( E MIN ) taken from an appropriate curve in the
Typical Operating Characteristics :
circuit efficiency for step-up regulators generally has an
LIR between 0.3 and 0.5. However, depending on the
AC characteristics of the inductor core material and ratio
I IN(DC,MAX) =
I MAIN(EFF) × V MAIN
V IN(MIN) ×η MIN
V IN(MIN) × ( V MAIN ? V IN(MIN) )
I RIPPLE =
I PEAK IN(DC,MAX) + RIPPLE
= I
of inductor resistance to other power-path resistances,
the best LIR can shift up or down. If the inductor resis-
tance is relatively high, more ripple can be accepted to
reduce the number of turns required and increase the
wire diameter. If the inductor resistance is relatively low,
increasing inductance to lower the peak current can
decrease losses throughout the power path. If extremely
thin high-resistance inductors are used, as is common
for LCD panel applications, the best LIR can increase to
between 0.5 and 1.0.
Once a physical inductor is chosen, higher and lower
values of the inductor should be evaluated for efficiency
improvements in typical operating regions.
In Figure 1, the LCD’s gate-on and gate-off supply
voltages are generated from two unregulated charge
pumps driven by the step-up regulator’s LX node. The
additional load on LX must therefore be considered in
the inductance and current calculations. The effective
maximum output current, I MAIN(EFF), becomes the sum
Calculate the ripple current at that operating point and
the peak current required for the inductor:
L × V MAIN × f OSC
I
2
The inductor’s saturation current rating and the
MAX17117 LX current limit should exceed I PEAK and the
inductor’s DC current rating should exceed I IN(DC,MAX) .
For good efficiency, choose an inductor with less than
0.1 I series resistance.
Considering the typical application circuit, the maximum
load current (I MAIN(MAX) ) is 200mA, with an 8.5V output
and a typical input voltage of 3.3V. The effective full-load
step-up current is:
I MAIN(EFF) = 200mA + 1 × 10mA + (2 + 1) × 25mA = 285mA
18
_____________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| MAX17120ETJ+ | IC DRVR SCAN TFT LDC 32-TQFN |
| MAX1714AEEP+T | IC REG CTRLR BUCK PWM CM 20-QSOP |
| MAX1715EEI | IC REG CTRLR BUCK PWM 28-QSOP |
| MAX1716EEG+ | IC REG CTRLR BUCK PWM CM 24-QSOP |
| MAX1717EEG+ | IC REG CTRLR BUCK PWM CM 24-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX17117ETJ+ | 功能描述:PMIC 解决方案 Internal-Switch Boost Regulator RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX17117ETJ+T | 功能描述:PMIC 解决方案 Internal-Switch Boost Regulator RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| MAX17117EVKIT+ | 功能描述:电源管理IC开发工具 MAX17117 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX17119ETI+ | 功能描述:LCD 驱动器 10Ch Scan Driver w/GPM RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
| MAX17119ETI+CH9 | 功能描述:LCD 驱动器 10Ch Scan Driver w/GPM RoHS:否 制造商:Maxim Integrated 数位数量:4.5 片段数量:30 最大时钟频率:19 KHz 工作电源电压:3 V to 3.6 V 最大工作温度:+ 85 C 最小工作温度:- 20 C 封装 / 箱体:PDIP-40 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。