- 您现在的位置：买卖IC网 > PDF目录15138 > MAX1717BEEG+T (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 24-QSOP PDF资料下载
参数资料
| 型号： | MAX1717BEEG+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 29/33页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 24-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1MHz |
| 占空比： | 100% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页
Dynamically Adjustable, Synchronous
Step-Down Controller for Notebook CPUs
V OUT = V FB ? 1 + ?
R INT ?
?
??
1 ? ?
?
?
Dropout Performance
The output voltage adjust range for continuous-conduc-
tion operation is restricted by the nonadjustable 500ns
(max) minimum off-time one-shot (375ns max at
1000kHz). For best dropout performance, use the slower
(200kHz) on-time settings. When working with low input
voltages, the duty-factor limit must be calculated using
worst-case values for on- and off-times. Manufacturing
tolerances and internal propagation delays introduce
an error to the TON K-factor. This error is greater at
higher frequencies (Table 3). Also, keep in mind that
transient response performance of buck regulators
operated close to dropout is poor, and bulk output
capacitance must often be added (see the VSAG equa-
tion in the Design Procedure section).
The absolute point of dropout is when the inductor cur-
rent ramps down during the minimum off-time ( Δ I DOWN )
as much as it ramps up during the on-time ( Δ I UP ). The
ratio h = Δ I UP / Δ I DOWN is an indicator of ability to slew
the inductor current higher in response to increased
load, and must always be greater than 1. As h
approaches 1, the absolute minimum dropout point, the
inductor current will be less able to increase during
each switching cycle and V SAG will greatly increase
unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but this may
be adjusted up or down to allow tradeoffs between
V SAG , output capacitance, and minimum operating
voltage. For a given value of h, the minimum operating
voltage can be calculated as:
V IN ( MIN ) = ( V OUT + V DROP 1 ) + V DROP 2 ? V DROP 1
? T OFF(MIN ) x h ?
? K
where V DROP1 and V DROP2 are the parasitic voltage
drops in the discharge and charge paths (see On-Time
One-Shot), T OFF(MIN) is from the Electrical Character-
istics , and K is taken from Table 3. The absolute minimum
input voltage is calculated with h = 1.
If the calculated V IN(MIN) is greater than the required
minimum input voltage, then operating frequency must
be reduced or output capacitance added to obtain an
acceptable V SAG . If operation near dropout is anticipat-
ed, calculate V SAG to be sure of adequate transient
response.
Dropout Design Example:
V OUT = 1.6V
f SW = 550kHz
K = 1.8μs, worst-case K = 1.58μs
T OFF(MIN) = 500ns
V DROP1 = V DROP2 = 100mV
h = 1.5
V IN(MIN) = (1.6V + 0.1V) / (1-0.5μs x 1.5/1.58μs) + 0.1V
- 0.1V = 3.2V
Calculating again with h = 1 gives the absolute limit of
dropout:
V IN(MIN) = (1.6V + 0.1V) / (1-1.0 ? 0.5μs/1.58μs) - 0.1V
+ 0.1V = 2.5V
Therefore, V IN must be greater than 2.5V, even with very
large output capacitance, and a practical input voltage
with reasonable output capacitance would be 3.2V.
Adjusting V OUT with a Resistor-Divider
The output voltage can be adjusted with a resistor-
divider rather than the DAC if desired (Figure 11). The
drawback is that the on-time doesn ’t automatically
receive correct compensation for changing output voltage
levels. This can result in variable switching frequency
as the resistor ratio is changed, and/or excessive
switching frequency. The equation for adjusting the output
voltage is:
? R 1 ?
R 2
where V FB is the currently selected DAC value, and
R INT is the FB input resistance. When using external
resistors, FBS remote sensing is not recommended, but
GNDS remote sensing is still possible. Connect FBS to
FB, and GNDS to a remote ground location. In resistor-
adjusted circuits, the DAC code should be set as close
as possible to the actual output voltage in order to mini-
mize the shift in switching frequency.
Adjusting V OUT Above 2V
The feed-forward circuit that makes the on-time depen-
dent on battery voltage maintains a nearly constant
switching frequency as V IN , I LOAD , and the DAC code
are changed. This works extremely well as long as FB
is connected directly to the output. When the output is
adjusted with a resistor divider, the switching frequency
is increased by the inverse of the divider ratio.
This change in frequency can be compensated with the
addition of a resistor-divider to the battery-sense input
(V+). Attach a resistor-divider from the battery voltage
to V+ on the MAX1717, with the same attenuation factor
as the output divider. The V+ input has a nominal input
impedance of 600k Ω , which should be considered
when selecting resistor values.
______________________________________________________________________________________
29
相关PDF资料 |
PDF描述 |
|---|---|
| UCD2A151MNQ1MS | CAP ALUM 150UF 100V 20% SMD |
| GBB15DHAS | CONN EDGECARD 30POS R/A .050 SLD |
| MAX1634CAI+T | IC REG CTRLR BUCK PWM CM 28-SSOP |
| GMM22DRSI-S288 | CONN EDGECARD 44POS .156 EXTEND |
| RBM06DTMT-S273 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1717EEG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1717EEG+ | 功能描述:DC/DC 开关控制器 Adj Synchronous Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1717EEG+C71058 | 功能描述:DC/DC 开关控制器 Step-Down Controller for Notebook CPU RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1717EEG+T | 功能描述:DC/DC 开关控制器 Adj Synchronous Step-Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1717EEG-C71058 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。