- 您现在的位置：买卖IC网 > PDF目录13148 > MAX1748EUE+ (Maxim Integrated Products)IC DC-DC CONV TRPL LCD 16-TSSOP PDF资料下载
参数资料
| 型号： | MAX1748EUE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 8/16页 |
| 文件大小： | 0K |
| 描述： | IC DC-DC CONV TRPL LCD 16-TSSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 96 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2.7 V ~ 5.5 V |
| 输出数： | 3 |
| 输出电压： | 2.7 V ~ 13 V |
| 工作温度： | 0°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 1410 (CN2011-ZH PDF) |
Triple-Output TFT-LCD
DC-DC Converters
Pin Description (continued)
PIN
8
9
10
11
12
13
14
15
16
NAME
FBN
SHDN
DRVN
SUPN
DRVP
SUPP
PGND
LX
TGND
FUNCTION
Negative Charge-Pump Regulator Feedback Input. Regulates to 0V nominal.
Active-Low Logic-Level Shutdown Input. Connect SHDN to IN for normal operation.
Negative Charge-Pump Driver Output. Output high level is V SUPN , and low level is PGND.
Negative Charge-Pump Driver Supply Voltage. Bypass to PGND with a 0.1μF capacitor.
Positive Charge-Pump Driver Output. Output high level is V SUPP , and low level is PGND.
Positive Charge-Pump Driver Supply Voltage. Bypass to PGND with a 0.1μF capacitor.
Power Ground. Connect to GND underneath the IC.
Main Boost Regulator Power MOSFET n-Channel Drain. Connect output diode and output capacitor
as close to PGND as possible.
Must be connected to ground.
Detailed Description
The MAX1748/MAX8726 are highly efficient triple-output
power supplies for TFT-LCD applications. These devices
contain one high-power step-up converter and two low-
power charge pumps. The primary boost converter uses
an internal n-channel MOSFET to provide maximum
efficiency and to minimize the number of external compo-
nents. The output voltage of the main boost converter
(V MAIN ) can be set from V IN to 13V with external resistors.
The dual charge pumps independently regulate a posi-
tive output (V POS ) and a negative output (V NEG ). These
low-power outputs use external diode and capacitor
stages (as many stages as required) to regulate output
voltages up to +40V and down to -40V. A proprietary
regulation algorithm minimizes output ripple as well as
capacitor sizes for both charge pumps.
Also included in the MAX1748/MAX8726 is a precision
1.25V reference that sources up to 50μA, logic shut-
down, soft-start, power-up sequencing, fault detection,
and an active-low open-drain ready output.
Main Boost Converter
The MAX1748/MAX8726 main step-up converter
switches at a constant 1MHz internal oscillator frequen-
cy to allow the use of small inductors and output
capacitors. The MOSFET switch pulse width is modulat-
ed to control the power transferred on each switching
cycle and to regulate the output voltage.
During PWM operation, the internal clock’s rising edge
sets a flip-flop, which turns on the n-channel MOSFET
(Figure 1). The switch turns off when the sum of the
voltage-error, slope-compensation, and current-feed-
back signals trips the multi-input comparator and
resets the flip-flop. The switch remains off for the rest of
the clock cycle. Changes in the output-voltage error
signal shift the switch current trip level, consequently
modulating the MOSFET duty cycle.
Dual Charge-Pump Regulator
The MAX1748/MAX8726 contain two individual low-
power charge pumps. One charge pump inverts the
supply voltage (SUPN) and provides a regulated nega-
tive output voltage. The second charge pump doubles
the supply voltage (SUPP) and provides a regulated
positive output voltage. The MAX1748/MAX8726 con-
tain internal p-channel and n-channel MOSFETs to con-
trol the power transfer. The internal MOSFETs switch at
a constant 500kHz (0.5 x f OSC ).
Negative Charge Pump
During the first half-cycle, the p-channel MOSFET turns
on and the flying capacitor C5 charges to V SUPN minus a
diode drop (Figure 2). During the second half-cycle, the
p-channel MOSFET turns off, and the n-channel MOSFET
turns on, level shifting C5. This connects C5 in parallel
with the reservoir capacitor C6. If the voltage across C6
minus a diode drop is lower than the voltage across C5,
charge flows from C5 to C6 until the diode (D5) turns off.
The amount of charge transferred to the output is
controlled by the variable n-channel on-resistance.
Positive Charge Pump
During the first half-cycle, the n-channel MOSFET turns
on and charges the flying capacitor C3 (Figure 3). This
initial charge is controlled by the variable n-channel on-
resistance. During the second half-cycle, the n-channel
MOSFET turns off and the p-channel MOSFET turns on,
level shifting C3 by V SUPP volts. This connects C3 in par-
allel with the reservoir capacitor C4. If the voltage across
C4 plus a diode drop (V POS + V DIODE ) is smaller than the
level-shifted flying capacitor voltage (V C3 + V SUPP ),
charge flows from C3 to C4 until the diode (D3) turns off.
8
_______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| ESRE221M0EB | CAP ALUM 220UF 2.5V 20% SMD |
| MAX871EUK+T | IC VOLT INVERT SW CAP SOT23-5 |
| ESRE151M06B-F | CAP ALUM 150UF 6.3V 20% SMD |
| ESM25DTMH-S189 | CONN EDGECARD 50POS R/A .156 SLD |
| AMM06DTMH-S189 | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1748EUE+ | 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1748EUE+T | 功能描述:直流/直流开关转换器 Triple-Output TFT LCD DC/DC Converters RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1748EUE-T | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1748EUE-TG069 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1748EVKIT | 功能描述:电源管理IC开发工具 MAX1748 Eval Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。