- 您现在的位置：买卖IC网 > PDF目录15036 > MAX17499BEUB+T (Maxim Integrated Products)IC REG CTRLR BST ISO PWM 10-UMAX PDF资料下载
参数资料
| 型号： | MAX17499BEUB+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/18页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST ISO PWM 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 625kHz |
| 占空比： | 75% |
| 电源电压： | 9.5 V ~ 24 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
Current-Mode PWM Controllers with
Programmable Switching Frequency
Choose a higher value for R1 than the one calculated in
the previous equation if a longer startup time can be
tolerated to minimize power loss on this resistor.
The above startup method is applicable to a circuit simi-
lar to the one shown in Figure 1. In this circuit, the ter-
tiary winding has the same phase as the output
windings. Thus, the voltage on the tertiary winding at any
given time is proportional to the output voltage and goes
through the same soft-start period as the output voltage.
The minimum discharge time of C1 from 21.6V to 9.74V
must be greater than the soft-start time of 5.6ms.
D1
Another method for bootstrapping the power supply is
to use a bias winding that is in-phase with the MOSFET
on-time (see Figure 5). In this case, the amount of
capacitance required at IN (C1) is much smaller.
However, the input voltage cannot have a range
greater than approximately 2:1 (primary-winding volt-
age to bias-winding voltage ratio).
For hiccup-mode fault protection, make the bias wind-
ing in-phase with the output, then the power-supply hic-
cups and soft-starts under output short-circuit
conditions. The power supply does not hiccup if the
bias winding is in-phase with the MOSFET on-time.
T1
V IN
D2
C4
V OUT
R1
UFLG
R2
R8
R9
IN
U1
NDRV
Q1
U2
OPTO
V CC
MAX17500A
CS
U2
OPTO LED
C3
TRANS
R7
R5
C1
COMP
GND
U3
TL431
FB
RT
UVLO/EN
R4
R10
C6
R6
C2
R12
R15
R3
Figure 5. Secondary-Side Regulated, Isolated Power Supply
______________________________________________________________________________________
13
相关PDF资料 |
PDF描述 |
|---|---|
| H2ABG-10102-B4-ND | JUMPER-H1503TR/A2015B/H1501TR 2" |
| DS1233-15+T&R/STR | IC ECONORESET NO PBR 15% TO92-3 |
| H2ABG-10102-A4-ND | JUMPER-H1503TR/A2015A/H1501TR 2" |
| VE-21T-EW-F3 | CONVERTER MOD DC/DC 6.5V 100W |
| EBC65DRTS-S13 | CONN EDGECARD 130POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1749EUK | 制造商:Maxim Integrated Products 功能描述:SOT23 VIBRATOR MOTOR DRIVER - Rail/Tube |
| MAX1749EUK+ | 制造商:Maxim Integrated Products 功能描述:STD REG 1.25V TO 6.5V/1.25V 0.12A 5PIN SOT-23 - Rail/Tube |
| MAX1749EUK+T | 功能描述:马达/运动/点火控制器和驱动器 Vibrator Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX1749EUK-T | 功能描述:马达/运动/点火控制器和驱动器 Vibrator Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MAX174ACPI | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。