- 您现在的位置：买卖IC网 > PDF目录19592 > MAX1805MEE+ (Maxim Integrated)IC TEMP SENSOR REMOTE 16-QSOP PDF资料下载
参数资料
| 型号： | MAX1805MEE+ |
| 厂商： | Maxim Integrated |
| 文件页数： | 10/17页 |
| 文件大小： | 497K |
| 描述： | IC TEMP SENSOR REMOTE 16-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 100 |
| 功能： | 温度计，恒温计 |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±3.5°C 本地（最大），±5°C 远程（最大） |
| 拓扑： | ADC，比较器，多路复用器，寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 3 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
sion cycle is truncated, and the data from that conversion
is not latched into either temperature-reading register. The
previous data is not changed and remains available.
In standby mode, supply current drops to about 3礎.
At very low supply voltages (under the power-on-reset
threshold), the supply current is higher due to the
address pin bias currents. It can be as high as 100礎,
depending on ADD0 and ADD1 settings.
SMBus Digital Interface
From a software perspective, the MAX1668/MAX1805/
MAX1989 appear as a set of byte-wide registers that
contain temperature data, alarm threshold values, or
control bits. A standard SMBus 2-wire serial interface is
used to read temperature data and write control bits and
alarm threshold data. Each A/D channel within the
devices responds to the same SMBus slave address for
normal reads and writes.
The MAX1668/MAX1805/MAX1989 employ four standard
SMBus protocols: write byte, read byte, send byte, and
receive byte (Figure 3). The shorter receive byte protocol
allows quicker transfers, provided that the correct data
register was previously selected by a read byte instruc-
tion. Use caution with the shorter protocols in multimaster
systems, since a second master could overwrite the com-
mand byte without informing the first master.
The temperature data format is 7 bits plus sign in twos-com-
plement form for each channel, with each data bit represent-
ing 1癈 (Table 2), transmitted MSB first. Measurements are
offset by +0.5癈 to minimize internal rounding errors; for
example, +99.6癈 is reported as +100癈.
Alarm Threshold Registers
Ten (six for MAX1805) registers store alarm threshold
data, with high-temperature (T
HIGH
) and low-tempera-
ture (T
LOW
) registers for each A/D channel. If either
measured temperature equals or exceeds the corre-
sponding alarm threshold value, an ALERT interrupt is
asserted.
The power-on-reset (POR) state of all T
HIGH
registers of
the MAX1668 and MAX1805 is full scale (0111 1111, or
+127癈). The POR state of the channel 1 T
HIGH
register
of the MAX1989 is 0110 1110 or +110癈, while all other
channels are at +127癈. The POR state of all T
LOW
reg-
isters is 1100 1001 or -55癈.
Multichannel Remote/Local
Temperature Sensors
10 ______________________________________________________________________________________
ACK
7 bits
ADDRESS
ACK
WR
8 bits
DATA
ACK
1
P
8 bits
S
COMMAND
Write Byte Format
Read Byte Format
Send Byte Format
Receive Byte Format
Slave Address: equiva-
lent to chip-select line of
a 3-wire interface
Command Byte: selects which
register you are writing to
Data Byte: data goes into the register
set by the command byte (to set
thresholds, configuration masks, and
sampling rate)
ACK
7 bits
ADDRESS
ACK
WR
S
ACK
8 bits
DATA
7 bits
ADDRESS
RD
8 bits
///
P
S
COMMAND
Slave Address: equiva-
lent to chip-select line
Command Byte: selects
which register you are
reading from
Slave Address: repeated
due to change in data-
flow direction
Data Byte: reads from
the register set by the
command byte
ACK
7 bits
ADDRESS
WR
8 bits
COMMAND
ACK
P
S
ACK
7 bits
ADDRESS
RD
8 bits
DATA
///
P
S
Command Byte: sends com-
mand with no data
Data Byte: This command only
works immediately following a
Read Byte. Reads data from the
register commanded by that last
Read Byte; also used for SMBus
Alert Response return address
S = Start condition
Shaded = Slave transmission
P = Stop condition
/// = Not acknowledged
Figure 3. SMBus Protocols
相关PDF资料 |
PDF描述 |
|---|---|
| LC51024VG-10F484I | IC XPLD 1024MC 10NS 484FPBGA |
| PQ1LA903MSPQ | IC REG LDO 9V .3A SOT-89 |
| MAX6697EP38+ | IC TEMP MON 7CH PREC 20-QSOP |
| 9250A-335-RC | CHOKE RF MOLDED 3300UH FERRITE |
| EMC40DRYI-S13 | CONN EDGECARD 80POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1805MEE+ | 功能描述:板上安装温度传感器 Remote/Local Temp w/SMBus Serial Int RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1805MEE+T | 功能描述:板上安装温度传感器 Remote/Local Temp w/SMBus Serial Int RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1805MEE-T | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MAX1806EUA08 | 功能描述:低压差稳压器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
| MAX1806EUA08+ | 功能描述:低压差稳压器 - LDO 500mA RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20 |
发布紧急采购，3分钟左右您将得到回复。