- 您现在的位置：买卖IC网 > PDF目录13562 > MAX1817EUB+ (Maxim Integrated Products)IC REG BOOST 125MA DL 10UMAX PDF资料下载
参数资料
| 型号： | MAX1817EUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST 125MA DL 10UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 类型： | 升压（升压） |
| 输出类型： | 两者兼有 |
| 输出数： | 2 |
| 输出电压： | 3.3V 或可调主电源，-28 V ~ 28 V 或可调副电源 |
| 输入电压： | 1.5 V ~ 5.5 V |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 125mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 10-µMAX |
Compact, High-Efficiency, Dual-Output
Step-Up DC-DC Converter
shown in Figure 3 are recommended for most applica-
V IN
C1
10 μ F
L1,10 μ H
R3
1
C6
0.1 μ F
D3*
D4*
-19V
V LCD
C5
1 μ F
tions, although values between 4.7μH and 47μH are
suitable. Smaller inductance values typically offer a
smaller physical size for a given series resistance,
allowing the smallest overall circuit dimensions. Larger
L2
10 μ H
LX
LXLCD
D2
D1**
inductance values exhibit higher output current capa-
bility, but larger physical dimensions.
Circuits using larger inductance values may start up at
lower input voltages and exhibit less ripple, but they
may provide reduced output power. This occurs when
the inductance is sufficiently large to prevent the maxi-
mum current limit from being reached before the maxi-
MAX1817
ONLCD
FBLCD
R1
240k
C4
10pF
C2
0.1 μ F
mum on-time expires. The inductor ’ s saturation current
rating should be greater than the peak switching cur-
rent. However, it is generally acceptable to bias most
ON
OUT
C3
MAIN
R2
16.5k
inductors into saturation by as much as 20%, although
this may slightly reduce efficiency.
FB
22 μ F
For best efficiency, select inductors with resistance no
AGND
GND
greater than the internal N-channel FET resistance in
*D3, D4 = CENTRAL SEMICONDUCTOR
CMPD7000 DUAL
**D1 = CENTRAL SEMICONDUCTOR
CMSD4448 (1N4148)
Figure 4. Negative Voltage for LCD Bias
Using a Charge Pump to Make Negative
LCD Output Voltage
The MAX1817 can generate a negative LCD output by
adding a diode-capacitor charge-pump circuit (D3, D4,
and C6) to the LXLCD pin as shown in Figure 4. FBLCD
is driven through a resistive voltage-divider from the
positive output, which is not loaded, allowing a very
small capacitor value at C2. For best stability and low-
est ripple, the time constant of the R1 + R2 series com-
bination and C2 should be near that of C5 and the
effective load resistance. Output load regulation of the
negative output degrades compared to the standard
positive output circuit and may rise at very light loads. If
this is not acceptable, reduce the resistance of R1 and
R2, while maintaining their ratio, to effectively preload
the output with a few hundred μA. This is why the R1
and R2 values shown in Figure 4 are lower than typical
values for a positive-output design. When loaded, the
magnitude of the negative output voltage is slightly
lower (closer to ground by approximately a diode for-
ward voltage) than the voltage on C2.
Applications Information
Inductor Selection
The MAX1817 ’ s high switching frequency allows the
use of small surface-mount inductors. The 10μH values
each step-up converter.
For maximum output current, choose L such that:
L < [(V IN ? t ON ) / I PEAK ]
where t ON is the maximum switch on-time (5μs for main
step-up converter) or 9μs for LCD step-up converter)
and I PEAK is the switch peak current limit (0.75A for the
main step-up converter, or 0.5A for the LCD step-up
converter). With this inductor value, the maximum output
current the main converter is able to deliver is given by:
I OUT(MAX) = 0.5 ? I PEAK / (1 + t ON / t OFF )
where t ON / t OFF = (V OUT + V D - V IN ) / (V IN - V ON ), V IN
and V OUT are the input and output voltages, V D is the
Schottky diode drop (0.3V typ), and V ON = I PEAK ?
R ON , where R ON is the switch on-resistance.
For V IN = 1.5V and V OUT = 3.3V, with a minimum I PEAK
value of 0.5A, and V ON(MAX) given by (0.5) ? (0.65) =
0.325V, the available output current that the converter
can provide is at least 90mA.
For larger inductor values, I PEAK is determined by:
I PEAK = [(V IN ? t ON ) / L]
External Rectifiers
The high maximum switching frequency of the
MAX1817 requires a high-speed rectifier. Schottky
diodes such as the Motorola MBR0530 or the Nihon
EP05Q03L are recommended. To maintain high effi-
ciency, the average current rating of the Schottky diode
should be greater than the peak switching current. A
junction diode such as the Central Semiconductor
CMPD4448 can be used for the LCD output with little
10
______________________________________________________________________________________
相关PDF资料 |
PDF描述 |
|---|---|
| 50THV47M10X10.5 | CAP ALUM 47UF 50V 20% SMD |
| UCW1V100MCL1GS | CAP ALUM 10UF 35V 20% SMD |
| VI-JNX-EX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
| GBB40DHRD | CONN CARD EXTEND 80POS .050" SLD |
| SC63LCB-4R7 | INDUCTOR SMD 4.7UH 1.66A 100KHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1817EUB+ | 功能描述:直流/直流开关转换器 Dual-Output Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1817EUB+T | 功能描述:直流/直流开关转换器 Dual-Output Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1817EUB-T | 功能描述:直流/直流开关转换器 Dual-Output Step-Up DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1817EVKIT | 制造商:Maxim Integrated Products 功能描述:COMPACT, HIGH-EFFICIENCY, DUAL-OUTPUT STEP-UP - Bulk |
| MAX1818ESA20 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
发布紧急采购，3分钟左右您将得到回复。