- 您现在的位置：买卖IC网 > PDF目录1840 > MAX1823AEUB+ (Maxim Integrated Products)IC SW USB DUAL W/FB 10-UMAX PDF资料下载
参数资料
| 型号： | MAX1823AEUB+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC SW USB DUAL W/FB 10-UMAX |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| 应用： | USB，外设 |
| 电流 - 电源： | 50µA |
| 电源电压： | 4 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-µMAX |
| 包装： | 管件 |
Dual USB Switch with Fault
Blanking and Autoreset
Table 1. MAX1823 Current Limiting and Fault Behavior
CONDITION
Output short circuit
?
?
MAX1823 BEHAVIOR
An output short circuit ramps the current to I SHORT in 2ms to 3ms, the switch shuts off, the
blanking timer turns on, FAULT_ stays high, and the output current pulses at 0.35A RMS .
Removing the short circuit before the 15ms short-circuit blanking timeout period allows the
next ramped current pulse to soft-start the output. The FAULT_ flag stays high.
(V OUT < 1V)
Output overload current
(V OUT > 1V)
Thermal fault
(T J > +160 ° C)
?
?
?
?
?
?
?
A short circuit exceeding 15ms to 20ms forces FAULT_ low at 20ms, enables autoreset
mode, and sources 25mA at the output.
An output voltage above 0.5V for 20ms resets the switch, turns on the output, and forces
FAULT_ high.
An output overload regulates the current at I LIM (0.9A), and FAULT_ stays high until the
overload is removed, a thermal fault occurs, or the 20ms continuous current-limit timeout
period is reached.
An overcurrent condition still present at 20ms forces FAULT_ low, enables autoreset, and
sources 25mA at the output.
An output voltage above 0.5V for 20ms resets the switch, turns on the output, and forces
FAULT_ high.
A junction temperature of +160 ° C immediately forces FAULT_ low (the blanking timer does
not apply to thermal faults) and turns off the switch. The junction cooling 15 ° C removes the
thermal fault condition, enables autoreset mode, and sources 25mA at the output. FAULT_
remains low while a thermal fault condition is present.
An output voltage above 0.5V for 20ms resets the switch, turns on the output, and forces
FAULT_ high.
Fault blanking allows the MAX1823 to handle USB loads
that may not be fully compliant with the USB specifica-
tions. USB loads with additional bypass capacitance
and/or large startup currents can be successfully pow-
ered even while protecting the upstream power source.
No fault is indicated if the switch is able to bring up the
load within the 20ms blanking period.
Applications Information
Input Power Source
IN, INA, and INB provide the power for all control and
charge-pump circuitry. All three IN_ pins must be con-
nected together externally. The input-voltage slew rate
should be less than 0.2V/μs to prevent erroneous
FAULT_ indications. This condition should not occur
under normal USB applications.
Input Capacitor
Connect a capacitor from IN_ to ground to limit the input
voltage drop during momentary output short-circuit con-
ditions. A 0.1μF ceramic capacitor is required for local
decoupling; higher capacitor values further reduce the
voltage drop at the input (see the Typical Application
Circuit (Figure 1)). When driving inductive loads, a larg-
er capacitance prevents voltage spikes from exceeding
the MAX1823 ’ s absolute maximum ratings.
Output Capacitor
Place a 1μF or greater capacitor at each output for noise
immunity. When starting up into very large capacitive
loads, the switch pulses the output current at 0.35A RMS
until the output voltage rises above 1V, then the capacitor
continues to charge at the full 0.9A current limit. There is
no limit to the output capacitor size, but to prevent a start-
up fault assertion, the capacitor must charge up within
the fault-blanking delay period. Typically, starting up into
a 330μF or smaller capacitor does not trigger a fault out-
put. In addition to bulk capacitance, small-value (0.1μF or
greater) ceramic capacitors improve the output ’ s
resilience to electrostatic discharge (ESD).
Driving Inductive Loads
A wide variety of devices (mice, keyboards, cameras,
and printers) can load the USB port. These devices com-
monly connect to the port with cables, which can add an
inductive component to the load. This inductance causes
the output voltage at the USB port to ring during a load
step. The MAX1823 is capable of driving inductive loads,
but avoids exceeding the device ’ s absolute maximum rat-
ings. Usually the load inductance is relatively small, and
the MAX1823 ’ s input includes a substantial bulk capaci-
tance from an upstream regulator as well as local bypass
capacitors, limiting overshoot. If severe ringing occurs
due to large load inductance, clamp the MAX1823 ’ s out-
put below 6V and above -0.3V.
______________________________________________________________________________________
11
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1830EEE+T | IC REG BUCK SYNC 3A 16QSOP |
| MAX1835EUT#TG16 | IC REG BOOST SYNC 3.3V SOT23-6 |
| MAX1836EUT33#TG16 | IC REG BUCK 3.3V 125MA SOT23-6 |
| MAX1838EEE+ | IC SW USB DUAL W/FB 16-QSOP |
| MAX1842EEE+T | IC REG BUCK SYNC 1A 16QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1823AEUB+ | 功能描述:电源开关 IC - USB Dual USB Switch w/Fault Blank RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1823AEUB+T | 功能描述:电源开关 IC - USB Dual USB Switch w/Fault Blank RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1823AEUB-T | 功能描述:电源开关 IC - USB Dual USB Switch w/Fault Blank RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1823BEUB | 功能描述:电源开关 IC - USB Dual USB Switch w/Fault Blank RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MAX1823BEUB+ | 功能描述:电源开关 IC - USB Dual USB Switch w/Fault Blank RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。