- 您现在的位置：买卖IC网 > PDF目录383338 > MAX1854 (Maxim Integrated Products, Inc.) High-Speed, Adjustable, Synchronous Step-Down Controllers with Integrated Voltage Positioning PDF资料下载
参数资料
| 型号： | MAX1854 |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Speed, Adjustable, Synchronous Step-Down Controllers with Integrated Voltage Positioning |
| 中文描述： | 高速、数字可调、同步降压型控制器，集成电压定位电路 |
| 文件页数： | 12/33页 |
| 文件大小： | 840K |
| 代理商： | MAX1854 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
M
High-Speed, Adjustable, Synchronous Step-Down
Controllers with Integrated Voltage Positioning
12
______________________________________________________________________________________
Pin Description
PIN
NAME
FUNCTION
1
DH
High-Side Gate Driver Output. DH swings from LX to BST.
2
V+
Battery Voltage Sense Connection. Connect V+ to input power source. V+ is used only for PWM
one-shot timing. DH on-time is inversely proportional to input voltage over a 2V to 28V range.
3
SHDN
Shutdown Control Input. Drive
SHDN
to GND to force the MAX1716/MAX1854/MAX1855 into
shutdown. Drive or connect to V
CC
for normal operation. A rising edge on
SHDN
clears the fault
latch.
4
FB
Feedback Input. Normally connected to V
OUT
. FB is connected to the bulk output filter capacitors
locally at the power supply. An external resistive divider can optionally set the output voltage.
5
CC
Voltage-Positioning Compensation Capacitor. Connect a 47pF to 1000pF (47pF typ) capacitor from
CC to GND to adjust the loop
’
s response time.
6
ILIM
Current-Limit Adjustment. The GND-CS current-limit threshold defaults to 120mV, if ILIM is tied to
V
CC
. In adjustable mode, the current-limit threshold voltage is 1/10th the voltage seen at ILIM over a
0.5V to 2.0V range. The logic threshold for switchover to the 120mV default value is approximately
V
CC
- 1V. Connect ILIM to REF for a fixed 200mV threshold.
7
V
CC
Analog Supply Input for PWM Core. Connect to the system supply voltage (+4.5V to +5.5V) with a
series 20
resistor. Bypass to GND with a 0.22
μ
F (min) ceramic capacitor.
8
TON
On-Time Selection-Control Input. This is a four-level input used to determine DH on-time. Connect to
GND, REF, or V
CC
, or leave TON unconnected to set the following switching frequencies: GND =
550kHz, REF = 400kHz, floating = 300kHz, and V
CC
= 200kHz.
9
REF
+2.0V Reference Voltage Output. Bypass to GND with 0.22
μ
F (min) capacitor. Can supply 50
μ
A for
external loads.
10
GND
Analog Gound
11
VPS
Voltage-Positioning Sense Input. Connect to CS through a 1k
resistor to maximize the load-
dependent output voltage drop, or adjust the voltage positioning level by connecting a resistive
divider from CS to PGND. Refer to
Setting Voltage Positioning
on how to select resistor values.
12
VGATE
Open-Drain Power-Good Output. VGATE is normally high when the output is in regulation. VGATE is
low in shutdown, undervoltage lockout, and during soft-start. Any fault condition forces VGATE low,
and it remains low until the fault is cleared.
13
DL
Low-Side Gate-Driver Output. DL swings from PGND to V
DD
.
14
PGND
Power Ground
15
V
DD
Supply Input for the DL Gate Drive. Connect to the system supply voltage, +4.5V to +5.5V. Bypass
to PGND with a 1
μ
F (min) ceramic capacitor.
16
D4
MSB DAC Code Input. 5
μ
A internal pullup to V
CC
(Table 5).
17
D3
DAC Code Input. 5
μ
A internal pullup to V
CC
(Table 5).
18
D2
DAC Code Input. 5
μ
A internal pullup to V
CC
(Table 5).
19
D1
DAC Code Input. 5
μ
A internal pullup to V
CC
(Table 5).
20
D0
LSB DAC Code Input. 5
μ
A internal pullup to V
CC
(Table 5).
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1857EUA47 | 500mA, Low-Dropout, Ripple-Rejecting LDO in MAX |
| MAX1857 | Replaced by TMS320C6202B : Fixed-Point Digital Signal Processor 352-FCBGA |
| MAX1858 | Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR |
| MAX1858EEG | Dual 180∑ Out-of-Phase PWM Step-Down Controller with Power Sequencing and POR |
| MAX1858A-MAX1876A | Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1854EEG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1854EEG/GG8 | 功能描述:DC/DC 开关控制器 High-Speed Adjustable Synchronous Step-Down Controllers with Integrated Voltage Positioning RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1854EEG+ | 制造商:Maxim Integrated Products 功能描述:HIGH-SPEED,DIGITALLY ADJUSTABLE SYNCHRONOUS STEPDOWN CONTROL - Rail/Tube |
| MAX1854EEG+T | 制造商: 功能描述: 制造商:undefined 功能描述: |
| MAX1854EEGT | 制造商: 功能描述: |
发布紧急采购，3分钟左右您将得到回复。