- 您现在的位置：买卖IC网 > PDF目录1841 > MAX1875AEEG+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM VM 24-QSOP PDF资料下载
参数资料
| 型号： | MAX1875AEEG+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 21/22页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 24-QSOP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电压模式 |
| 输出数： | 2 |
| 频率 - 最大： | 660kHz |
| 电源电压： | 4.5 V ~ 23 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 24-SSOP（0.154"，3.90mm 宽） |
| 包装： | 管件 |
Dual 180° Out-of-Phase Buck Controllers with
Sequencing/Prebias Startup and POR
? Use a star-ground connection on the power plane to
minimize the crosstalk between OUT1 and OUT2.
? Keep the high-current paths short, especially at the
ground terminals. This practice is essential for sta-
ble, jitter-free operation.
? Connect GND and PGND together close to the IC.
Do not connect them together anywhere else.
Carefully follow the grounding instructions under
step 4 of the Layout Procedure section.
? Keep the power traces and load connections short.
This practice is essential for high efficiency. Use
thick copper PC boards (2oz vs. 1oz) to enhance
full-load efficiency by 1% or more.
? LX_ and PGND connections to the synchronous rec-
tifiers for current limiting must be made using Kelvin-
sense connections to guarantee the current-limit
accuracy. With 8-pin SO MOSFETs, this is best done
by routing power to the MOSFETs from outside
using the top copper layer, while connecting PGND
and LX_ underneath the 8-pin SO package.
? When trade-offs in trace lengths must be made,
allow the inductor-charging path to be made longer
than the discharge path. Since the average input
current is lower than the average output current in
step-down converters, this minimizes the power dis-
sipation and voltage drops caused by board resis-
tance. For example, allow some extra distance
between the input capacitors and the high-side
MOSFET rather than to allow distance between the
inductor and the low-side MOSFET or between the
inductor and the output filter capacitor.
? Ensure that the feedback connection to C OUT_ is
short and direct.
? Route high-speed switching nodes (BST_, LX_, DH_,
and DL_) away from the sensitive analog areas
(REF, COMP_, ILIM_, and FB_). Use PGND1 and
PGND2 as EMI shields to keep radiated noise away
from the IC, feedback dividers, and analog bypass
capacitors.
? Make all pin-strap control input connections (ILIM_,
SYNC, and EN) to analog ground (GND) rather than
power ground (PGND).
Layout Procedure
1) Place the power components first, with ground termi-
nals adjacent (N L _ source, C IN _, and C OUT _). Make
all these connections on the top layer with wide, cop-
per-filled areas (2oz copper recommended).
2) Mount the controller IC adjacent to the synchronous-
rectifier MOSFETs (N L _), preferably on the back
side in order to keep LX_, PGND_, and DL_ traces
short and wide. The DL_ gate trace must be short
and wide, measuring 50mils to 100mils wide if the
low-side MOSFET is 1in from the controller IC.
3) Group the gate-drive components (BST_ diodes and
capacitors, and V L bypass capacitor) together near
the controller IC.
4) Make the DC-DC controller ground connections as
follows: create a small analog ground plane near the
IC. Connect this plane to GND and use this plane for
the ground connection for the reference (REF) V+
bypass capacitor, compensation components, feed-
back dividers, OSC resistor, and ILIM_ resistors (if
any). Connect GND and PGND together under the
IC (this is the only connection between GND and
PGND).
5) On the board’s top side (power planes), make a star
ground to minimize crosstalk between the two sides.
Chip Information
TRANSISTOR COUNT: 6688
PROCESS: BiCMOS
______________________________________________________________________________________
21
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1876EEG+T | IC REG CTRLR BUCK PWM VM 24-QSOP |
| MAX1878ETC+ | IC REG BUCK BST SYNC ADJ 12TQFN |
| MAX1879EUA+T | IC CHARGER LI+ PULSE 8UMAX |
| MAX1880EUG+ | IC DC-DC CONV QUAD LCD 24TSSOP |
| MAX1889ETE+T | IC PWR SUP TRPL LCD 16-TQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1875AEEG+ | 功能描述:电压模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1875AEEG+T | 功能描述:电压模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX1875AEEG-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1875EEG | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1875EEG+ | 功能描述:电压模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。