- 您现在的位置：买卖IC网 > PDF目录9886 > MAX187CEWE+T (Maxim Integrated Products)IC ADC 12BIT SERIAL LP 16SOIC PDF资料下载
参数资料
| 型号： | MAX187CEWE+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 18/18页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT SERIAL LP 16SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 1,000 |
| 位数： | 12 |
| 采样率（每秒）： | 75k |
| 数据接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 478mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极 |
MAX187/MAX189
+5V, Low-Power, 12-Bit Serial ADCs
9
Maxim Integrated
Figure 5. MAX187/MAX189 Shutdown Sequence
Input Protection
Internal protection diodes that clamp the analog input
allow the input to swing from GND - 0.3V to VDD + 0.3V
without damage. However, for accurate conversions near
full scale, the input must not exceed VDD by more than
50mV, or be lower than GND by 50mV.
If the analog input exceeds the supplies by more than
50mV beyond the supplies, limit the input current
to 2mA, since larger currents degrade conversion
accuracy.
Driving the Analog Input
The input lines to AIN and GND should be kept as short
as possible to minimize noise pickup. Shield longer
leads. Also see the Input Protection section.
Because the MAX187/MAX189 incorporate a T/H, the
drive requirements of the op amp driving AIN are less
stringent than those for a successive-approximation ADC
without a T/H. The typical input capacitance is 16pF. The
amplifier bandwidth should be sufficient to handle the
frequency of the input signal. The MAX400 and OP07
work well at lower frequencies. For higher-frequency
operation, the MAX427 and OP27 are practical choices.
The allowed input frequency range is limited by the
75ksps sample rate of the MAX187/MAX189. Therefore,
the maximum sinusoidal input frequency allowed is
37.5kHz. Higher-frequency signals cause aliasing prob-
lems unless undersampling techniques are used.
Reference
The MAX187 can be used with an internal or external ref-
erence, while the MAX189 requires an external reference.
Internal Reference
The MAX187 has an on-chip reference with a buff-
ered temperature-compensated bandgap diode, laser-
trimmed to +4.096V Q0.5%. Its output is connected to
REF and also drives the internal DAC. The output can be
used as a reference voltage source for other components
and can source up to 0.6mA. Decouple REF with a 4.7FF
capacitor. The internal reference is enabled by pulling
the SHDN pin high. Letting SHDN float disables the inter-
nal reference, which allows the use of an external refer-
ence, as described in the External Reference section.
External Reference
The MAX189 operates with an external reference at the
REF pin. To use the MAX187 with an external reference,
disable the internal reference by letting SHDN float. Stay
within the voltage range +2.5V to VDD to achieve speci-
fied accuracy. The minimum input impedance is 12kI for
DC currents. During conversion, the external reference
must be able to deliver up to 350FA DC load current and
have an output impedance of 10I or less. The recom-
mended minimum value for the bypass capacitor is 0.1FF.
If the reference has higher output impedance or is noisy,
bypass it close to the REF pin with a 4.7FF capacitor.
DOUT
CS
SHDN
CONVERSION 1
tWAKE
COMPLETE CONVERSION SEQUENCE
POWERED DOWN
POWERED UP
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1275AETC+ | IC ADC 12BIT 1.8MSPS 12-TQFN |
| MAX1225ETC+ | IC ADC 12BIT 1.5MSPS 12-TQFN |
| ISL32485EIBZ-T | IC TXRX RS485 FAULT PROT 8SOIC |
| ISL4221EIRZ-T | IC XMITTER/RCVR ESD RS232 16-QFN |
| MS3100A28-11P | CONN RCPT 22POS WALL MNT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX187EVC16-DIP | 功能描述:模数转换器 - ADC Programmers, Development Systems RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX187EVKIT-DIP | 功能描述:数据转换 IC 开发工具 Programmers, Development Systems RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MAX1880EUG | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1880EUG+ | 功能描述:直流/直流开关转换器 Quad-Output TFT LCD RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1880EUG+T | 功能描述:直流/直流开关转换器 Quad-Output TFT LCD RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。