- 您现在的位置：买卖IC网 > PDF目录383340 > MAX189 (Maxim Integrated Products, Inc.) +5V, Low-Power, 12-Bit Serial ADCs(8.5μs转换时间，单通道，串行12位A/D转换器) PDF资料下载
参数资料
| 型号： | MAX189 |
| 厂商： | Maxim Integrated Products, Inc. |
| 元件分类： | ADC |
| 英文描述： | +5V, Low-Power, 12-Bit Serial ADCs(8.5μs转换时间，单通道，串行12位A/D转换器) |
| 中文描述： | +5V、低功耗、12位串行ADC |
| 文件页数： | 17/20页 |
| 文件大小： | 177K |
| 代理商： | MAX189 |
M
+5V, Low-Power, 12-Bit S erial ADCs
______________________________________________________________________________________
17
SUPPLIES
+5V
GND
DGND
+5V
DIGITAL
CIRCUITRY
DGND
AGND
VDD
MAX187
MAX189
*OPTIONAL
R* = 10
4.7
μ
F
0.01
μ
F
The ADC results are transmitted across a 1500V isola-
tion barrier provided by three 6N136 opto-isolators.
Isolated power must be supplied to the converter and
the isolated side of the opto-couplers. 74HC595 three-
state shift registers are used to construct a 12-bit paral-
lel data output. The timing sequence is identical to the
timing shown in Figure 8. Conversion speed is limited
by the delay through the opto-isolators. With a 140kHz
clock, conversion time is 100μs.
The universal 12-bit parallel data output can also be
used without the isolation stage when a parallel inter-
face is required. Clock frequencies up to 2.9MHz are
possible without violating the 20ns shift-register setup
time. Delay or invert the clock signal to the shift regis-
ters beyond 2.9MHz.
Layout, Grounding, Bypassing
For best performance, use printed circuit boards. Wire-
wrap boards are not recommended. Board layout
should ensure that digital and analog signal lines are
separated from each other. Do not run analog and digi-
tal (especially clock) lines parallel to one another, or
digital lines underneath the ADC package.
Figure 17 shows the recommended system ground
connections. A single-point analog ground (“star”
ground point) should be established at GND, separate
from the logic ground. All other analog grounds should
be connected to this ground. The 16-pin versions also
have a dedicated DGND pin available. Connect DGND
to this star ground point for further noise reduction. No
other digital system ground should be connected to
this single-point analog ground. The ground return to
the power supply for this ground should be low imped-
ance and as short as possible for noise-free operation.
High-frequency noise in the V
power supply may
affect the ADC’s high-speed comparator. Bypass this
supply to the single-point analog ground with 0.01μF
and 4.7μF bypass capacitors. Minimize capacitor lead
lengths for best supply-noise rejection. If the +5V
power supply is very noisy, a 10
resistor can be con-
nected as a lowpass filter to attenuate supply noise
(Figure 17).
Figure 17. Power-Supply Grounding Condition
相关PDF资料 |
PDF描述 |
|---|---|
| MAX187ACWE | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX187AMJA | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX187CEPA | +5V, Low-Power, 12-Bit Serial ADCs |
| MAX189CEPA | 031-0560-161 |
| MAX189BEWE | CANMS3121E16-26SF0 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1894EVKIT | 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MAX1894XEEE | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1894XEEE-T | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1895EGI | 功能描述:显示驱动器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| MAX1895EGI-T | 功能描述:显示驱动器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。