- 您现在的位置：买卖IC网 > PDF目录383341 > MAX1906SEGE (MAXIM INTEGRATED PRODUCTS INC) Li+ Battery-Pack Protector with Integrated Fuse Driver PDF资料下载
参数资料
| 型号： | MAX1906SEGE |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 电源管理 |
| 英文描述： | Li+ Battery-Pack Protector with Integrated Fuse Driver |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, CQCC16 |
| 封装： | 5 X 5 MM, 0.90 MM HEIGHT, QFN-16 |
| 文件页数： | 5/14页 |
| 文件大小： | 325K |
| 代理商： | MAX1906SEGE |
Detailed Description
The MAX1906 protects 2-, 3-, or 4-series Li+ battery
packs from overcharge by controlling a three-terminal
protection fuse. Figures 1 and 2 show two application
circuits using the MAX1906. The MAX1906 checks the
voltage of each cell at regular intervals. An overcharge
condition is detected if any cell voltage exceeds the
overvoltage threshold for more than 2.1s. The MAX1906
responds to an overcharge condition by turning on an
internal SCR (Figure 1) or an external MOSFET (Figure 2)
to blow a three-terminal protection fuse placed in series
with the charging path.
The MAX1906 checks for disconnected voltage sense
pins every time it exits the standby mode or test mode. If
a disconnected pin is detected, the DISCON pin is
latched low. The MAX1906 also includes a test mode,
which determines if the circuit is operating correctly while
in an assembled battery pack. A pulse on the TEST pin
enables the test mode. Figure 3 shows the cell connec-
tions for 2- and 3-series battery packs and Figure 4
shows the functional diagram for the MAX1906.
The MAX1906 can be used together with other
resettable protection circuits to provide a high level of
safety against overcharging Li+ batteries. Figure 5 shows
a typical application circuit using the MAX1906 together
with the MAX1924. The MAX1924 has a lower overvoltage
threshold than the MAX1906. If any cell voltage exceeds
4.35V (typ), the MAX1924 turns off the
TKO
and
CGO
MOSFETs and opens the charging path. If the
TKO
or
CGO
MOSFET fails and charging continues, the
MAX1906 blows the protection fuse and opens the charg-
ing path permanently once any cell voltage reaches
4.45V (typ). The MAX1924 also protects the battery pack
against undervoltage, charge current, discharge current,
and pack-short fault conditions. Refer to the MAX1894/
MAX1924 data sheets for complete details.
M
Li+ Battery-Pack Protector with
Integrated Fuse Driver
_______________________________________________________________________________________
5
Pin Description
PIN
MAX1906S
1, 9
6, 11, 13, 15
MAX1906V
1, 9
6, 11, 13, 15
MAX1906X
1, 9
6, 11, 13, 15
NAME
DESCRIPTION
I.C.
N.C.
Internal Connection. Float pins 1 and 9.
No Connection
2
2
2
DRV
MOSFET Driver Output. High when an overvoltage condition is detected.
Connect the DRV pin to the gate of an external MOSFET to blow the
protection fuse.
3
3
3
TEST
Test-Mode Input. Test mode is enabled with a pulse of minimum 50μs
duration on the TEST pin.
4
4
4
DISCON
Disconnected Pin Output. This is an open-drain output and is high-Z during
normal operation. If B4P, B3P, B2P, or B1P is disconnected, this pin is
pulled low (see the
Disconnected Pin Detection
section).
5
5
5
PKN
Pack Negative. A sense resistor may be connected between BN and PKN.
7
7
7
OUT
Anode Output of the SCR. Connect OUT to the fuse
’
s heater connection (see
the
Protection Fuse Selection
section).
8
8
8
BN
Negative Terminal of Cell 1. Connect BN to the negative terminal of the first
series Li+ cell. BN is also chip ground, which is connected to the backside
paddle on the QFN package.
10
10
10
B1P
Positive Terminal of Cell 1. Connect B1P to the positive terminal of the first
series Li+ cell.
12
12
12
B2P
Positive Terminal of Cell 2. Connect B2P to the positive terminal of the
second series Li+ cell.
—
14
14
B3P
Positive Terminal of Cell 3. Connect B3P to the positive terminal of the third
series Li+ cell.
—
—
16
B4P
Positive Terminal of Cell 4. Connect B4P to the positive terminal of the fourth
series Li+ cell.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1906V | Li+ Battery-Pack Protector with Integrated Fuse Driver |
| MAX1906VEGE | Li+ Battery-Pack Protector with Integrated Fuse Driver |
| MAX1906X | Li+ Battery-Pack Protector with Integrated Fuse Driver |
| MAX1924 | Advanced Li+ Battery-Pack Protectors |
| MAX1894XEEE | Advanced Li+ Battery-Pack Protectors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1906VEEE | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1906VEGE | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1906VEGE-T | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1906XEEE | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX1906XEGE | 功能描述:电池管理 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。