- 您现在的位置：买卖IC网 > PDF目录15533 > MAX1909ETI+T (Maxim Integrated Products)IC CHARGER BATTERY 28-TQFN PDF资料下载
参数资料
| 型号： | MAX1909ETI+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 19/30页 |
| 文件大小： | 0K |
| 描述： | IC CHARGER BATTERY 28-TQFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 功能： | 充电管理 |
| 电池化学： | 多化学 |
| 电源电压： | 8 V ~ 28 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 供应商设备封装： | 28-TQFN-EP（5x5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Multichemistry Battery Chargers with Automatic
System Power Selector
The body diode of the PDL switch prevents the voltage
on the power source output from collapsing.
Charging can also be inhibited by driving ICTL below
0.035V, which suspends switching and pulls CCI, CCS,
and CCV to ground. The PDS and PDL drivers, LDO,
input current monitor, and control logic (ACOK) all
remain active in this state. Approximately 3mA of sup-
ply current is drawn from the AC adapter and 3μA
(max) is drawn from the battery to support these
functions.
In smart-battery systems, PKPRES is usually driven from a
voltage-divider formed with a low-value resistor or PTC
thermistor inside the battery pack and a local resistive
pullup. This arrangement automatically detects the pres-
ence of a battery. The MAX8725 threshold voltage is 55%
of V LDO , with hysteresis of 1% V LDO to prevent erratic
transitions.
AC Adapter Detection and
Power-Source Selection
The MAX1909/MAX8725 include a hysteretic compara-
tor that detects the presence of an AC power adapter
and automatically delivers power to the system load
from the appropriate available power source. When the
adapter is present, the open-drain ACOK output
becomes high impedance. The switch threshold at
ACIN is 2.048V. Use a resistive voltage-divider from the
adapter’s output to the ACIN pin to set the appropriate
detection threshold. When charging, the battery is iso-
lated from the system load with the p-channel PDL
switch, which is biased off. When the adapter is absent,
the drives to the switches change state in a fast break-
before-make sequence. PDL begins to turn on 7.5μs
after PDS begins to turn off.
The threshold for selecting between the PDL and PDS
switches is set based on the voltage difference
between the DCIN and the BATT pins. If this voltage
difference drops below 100mV, the PDS is switched off
and PDL is switched on. Under these conditions, the
MAX1909/MAX8725 are completely powered down.
The PDL switch is kept on with a 100k Ω pulldown resis-
tor when the charger is powered down through ICTL or
PKPRES , or when the AC adapter is removed.
The drivers for PDL and PDS are fully integrated. The pos-
itive bias inputs for the drivers connect to the SRC pin and
the negative bias inputs connect to a negative regulator
referenced to SRC. With this arrangement, the drivers can
swing from SRC to approximately 10V below SRC.
Conditioning Mode
The MAX1909/MAX8725 can be programmed to per-
form a conditioning cycle to calibrate the battery’s fuel
gauge. This cycle consists of isolating the battery from
the charger and discharging it through the system load.
When the battery reaches 100% depth of discharge, it
is then recharged. Driving the MODE pin low places the
MAX1909/MAX8725 in conditioning mode, which stops
the charger from switching, turns the PDS switch off,
and turns the PDL switch on.
To utilize the conditioning mode function, the configura-
tion of the PDS switch must be changed to two source-
connected FETs to prevent the AC adapter from sup-
plying current to the system through the MOSFET ’s
body diode. See Figure 2. The SRC pin must be con-
nected to the common source node of the back-to-back
FETs to properly drive the MOSFETs.
It is essential to alert the user that the system
is performing a conditioning cycle. If the user termi-
nates the cycle prematurely, the battery can be dis-
charged even though the system was running off the
AC adapter for a substantial period of time. If the AC
adapter is in fact removed during conditioning, the
MAX1909/MAX8725 keep the PDL switch on and the
charger remains off as it would in normal operation.
In the MAX8725, if the battery is removed during condi-
tioning mode, the PKPRES control overrides condition-
ing mode. When MODE is grounded and PKPRES goes
high, the PDS switch starts turning on within 7.5μs and
the system is powered from the AC adapter.
In the MAX1909, disable conditioning mode before the
battery is overdischarged or removed.
DC-DC Converter
The MAX1909/MAX8725 employ a buck regulator with a
PMOS high-side switch and a low-side NMOS synchro-
nous rectifier. The MAX1909/MAX8725 feature a pseu-
do-fixed-frequency, cycle-by-cycle current-mode
control scheme. The off-time is dependent upon V DCIN ,
V BATT , and a time constant, with a minimum t OFF of
300ns. The MAX1909/MAX8725 can also operate in
discontinuous conduction for improved light-load effi-
ciency. The operation of the DC-DC controller is deter-
mined by the following four comparators as shown in
Figure 4:
? CCMP: Compares the control point (lowest voltage
clamp (LVC)) against the charge current (CSI). The
high-side MOSFET on-time is terminated if the CCMP
output is high.
______________________________________________________________________________________
19
相关PDF资料 |
PDF描述 |
|---|---|
| EBC18DRES-S734 | CONN EDGECARD 36POS .100 EYELET |
| V48C15C75BF | CONVERTER MOD DC/DC 15V 75W |
| V48C15C75BL3 | CONVERTER MOD DC/DC 15V 75W |
| RCC17DCST-S288 | CONN EDGECARD 34POS .100 EXTEND |
| MAX8934EETI+ | IC BATTERY CHARGER DUAL 28WQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1909EVKIT | 功能描述:电池管理 Evaluation Kit for the MAX1909 RoHS:否 制造商:Texas Instruments 电池类型:Li-Ion 输出电压:5 V 输出电流:4.5 A 工作电源电压:3.9 V to 17 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:VQFN-24 封装:Reel |
| MAX190ACNG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX190ACNG+ | 功能描述:模数转换器 - ADC 12Bit 75ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX190ACWG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MAX190ACWG+ | 功能描述:模数转换器 - ADC 12Bit 75ksps 5V Precision ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。