- 您现在的位置：买卖IC网 > PDF目录383341 > MAX1921EUT (Maxim Integrated Products, Inc.) PLASTIC ENCAPSULATED DEVICES PDF资料下载
参数资料
| 型号： | MAX1921EUT |
| 厂商： | Maxim Integrated Products, Inc. |
| 英文描述： | PLASTIC ENCAPSULATED DEVICES |
| 中文描述： | 塑封器件 |
| 文件页数： | 8/9页 |
| 文件大小： | 370K |
| 代理商： | MAX1921EUT |
M
MAX1921 Using Ceramic C
OUT
When using the application circuit of Figure 1, the
inductor
’
s series resistance causes a small amount of
load regulation, as desired for a voltage-positioning
load transient response. Choose R1 such that V
OUT
is
high at no load by about half of this load regulation. The
simplified calculation is:
where R
L
(MAX) is the maximum series resistance of the
inductor. Select a standard resistor value that is within
20% of this calculation.
Next, calculate C
FF
for 25mV ripple at the internal feed-
back node. The simplified calculation is:
where R1 is the standard resistor value that is used.
Select a standard capacitor value that is within 20% of
the calculated C
FF
.
MAX1920 Using Ceramic C
OUT
When using the application circuit of Figure 2, the induc-
tor
’
s series resistance causes a small amount of load
regulation, as desired for a voltage-positioning load tran-
sient response. Choose R1 and R2 such that V
OUT
is
high at no load by about half of this load regulation:
where R2 is chosen in the 50k
to 500k
range, V
REF
= 1.25V and R
L
is the typical series resistance of the
inductor. Use 1% or better resistors.
Next, calculate the equivalent resistance at the FB node as:
Then, calculate C
FF
for 25mV ripple at FB. The simpli-
fied calculation is:
Select a standard capacitor value that is within 20% of
the calculated C
FF
.
MAX1920 Using Tantalum C
OUT
When using the application circuit of Figure 4, choose
R1 and R2 such as to obtain the desired V
OUT
:
where R2 is chosen to be less than 50k
and V
REF
=
1.25V. Use 1% or better resistors.
Layout Considerations
High switching frequencies make PC board layout a
very important part of design. Good design minimizes
excessive EMI on the feedback paths and voltage gra-
dients in the ground plane, both of which can result in
instability or regulation errors. Connect the inductor,
input filter capacitor, and output filter capacitor as
close to the device as possible, and keep their traces
short, direct, and wide. Connect their ground pins at a
single common node in a star ground configuration.
The external voltage-feedback network should be very
close to the FB pin, within 0.2in (5mm). Keep noisy
traces, such as the LX trace, away from the voltage-
feedback network; also keep them separate, using
grounded copper. The MAX1920/MAX1921 evaluation
kit data sheet includes a proper PC board layout and
routing scheme.
R
R
V
V
OUT
REF
1
2
1
=
×
C
q
FF
=
2.
10
5
Re
Re
||
+
q
R
R
R
R
R
R
=
=
×
1
2
1
1
2
2
R
R
V
R
I
MAX
(
V
OUT
L
OUT
REF
1
2
2
1
=
×
+
×
)/
C
R
FF
=
2.
10
1
5
R
R MAX
(
1 5
10
4
×
×
)
Low-Voltage, 400mA Step-Down
DC-DC Converters in SOT23
8
_______________________________________________________________________________________
Table 3. Component Suppliers
SUPPLIER
Coilcraft
Kemet
Murata
PHONE
847-639-6400
408-986-0424
814-237-1431
847-956-0666
81-3-3607-5111
408-573-4150
81-3-3833-5441
847-297-0070
81-3-3727-1161
WEBSITE
www.coilcraft.com
www.kemet.com
www.murata.com
USA
Japan
USA
Japan
USA
Japan
Sumida
www.sumida.com
www.T-Yuden.com
www.yuden.co.jp
www.tokoam.com
www.toko.co.jp
Taiyo
Yuden
Toko
MAX1920
AGND
IN
SHDN
LX
PGND
FB
OFF
ON
R1
C
OUT
L
OUTPUT
UP TO 400mA
INPUT
2V TO 5.5V
C
IN
R2
2
1
3
5
6
4
Figure 4. MAX1920 Application Circuit Using Tantalum Output
Capacitor
相关PDF资料 |
PDF描述 |
|---|---|
| MAX1920EUT-T | Low-Voltage, 400mA Step-Down DC-DC Converters in SOT23 |
| MAX1921EUT-T | Low-Voltage, 400mA Step-Down DC-DC Converters in SOT23 |
| MAX1922 | 1A Current-Limited Switch for 2 USB Ports |
| MAX1922ESA | 1A Current-Limited Switch for 2 USB Ports |
| MAX1924X | Li+ Battery-Pack Protector with Integrated Fuse Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1921EUT15 | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE 400MA STEP-DOWN DC-DC - Cut Tape Product |
| MAX1921EUT15+ | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE 400MA STEP-DOWN DC-DC - Rail/Tube |
| MAX1921EUT15+T | 功能描述:直流/直流开关转换器 400mA Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1921EUT15-T | 功能描述:直流/直流开关转换器 400mA Step-Down DC/DC Converter RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| MAX1921EUT18 | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE 400MA STEP-DOWN DC-DC - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。